NOTE: Set the SOLENOID A switch to the A NORM position after
____ each condition.
~............................................................................. |CONDITION| HYDRUALIC | SOLENOID | RIGHT ELEVATOR | TOTAL TRAVEL | | | | | POSITION (MAX) | DISTANCE (MIN) | | ............... ....................... | | | A | B | A | UP (X) | DOWN (Y) | (X) + (Y) | ............................................................................... | 1 | ON | ON | +HDOVR | 1.38" | | | | | | | | (1.70°) | | | ........................................................... 1.78" (3.00°) | | 2 | ON | ON | -HDOVR | | 1.34" | | | | | | | | (1.70°) | | 2.........…......…......…...........…..........…..........…...................1
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-26
ALL ú ú 02 Page 509 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(d) (e) (f) Set the POWER switch to the OFF position.Set the horizontal stabilizer to 6 units of trim (B dimension is at 37.28 |0.05 inches).Find the index mark of the elevator: 1) Move the captain's control column lightly to make sure that the system is in the center. 2) Make a mark of the trailing edge of the right elevator on the side of the tail cone.
NOTE:____ This is the reference position of the right elevator for other measurements.
(g) (h) (i) Set the power switch to the ON position.Use the POSITION CONTROL A switch to align the elevator to the mark on the tail cone |0.06 inch. Lock the POSITION CONTROL A in its position.Set up the conditions as shown in the table below. Make sure that the right elevator positions are in the tolerances as in the table.
NOTE:____ Set the SOLENOID A switch to the A NORM position after each position.
~.............................................................................
|CONDITION| HYDRUALIC | SOLENOID | RIGHT ELEVATOR | TOTAL TRAVEL |
| | | | POSITION (MAX) | DISTANCE (MIN) |
| ............. .. ....................... |
| | A | B | A | UP (X) | DOWN (Y) | (X) + (Y) |
............................................................................... | 1 | ON | ON | +HDOVR | 5.27" | | | | | | | | (8.85°) | | | ........................................................... 4.08" | | 2 | ON | ON | -HDOVR | | 3.30" | (6.85°) | | | | | | | (5.55°) | | 2.........…......…......…...........…..........…..........…...................1
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
22-11-26
ALL ú ú 02 Page 510 ú Mar 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(j) Set the SOLENOID A to the A NORM position.
(k) Use the POSITION CONTROL B switch to align the elevator to the
mark on the tail cone |0.06 inch. Lock the POSITON CONTROL B
in its position.
(l) Set the switches on the test set as shown on the step
2.G.(3)(h).
(m) Set up the conditions as shown in the table below. Make sure
that the right elevator positions are in the tolerances as in
the table.
NOTE:____ Set the SOLENOID B switch to the B NORM position after
each condition.
~.............................................................................
|CONDITION| HYDRUALIC | SOLENOID | RIGHT ELEVATOR | TOTAL TRAVEL |
| | | | POSITION (MAX) | DISTANCE (MIN) |
| ............. .. ....................... |
| | A | B | B | UP (X) | DOWN (Y) | (X) + (Y) |
............................................................................... | 1 | ON | ON | +HDOVR | 5.27" | | | | | | | | (8.85°) | | | ........................................................... 4.08" | | 2 | ON | ON | -HDOVR | | 3.30" | (6.85°) | | | | | | | (5.55°) | | 2.........…......…......…...........…..........…..........…...................1 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 自動飛行 AUTOFLIGHT 2(7)
