曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 ALL  ú ú 01 Page 403 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
C76763
A
747-400 MAINTENANCE MANUAL
 RETRACTABLE CENTER GUIDE/RESTRAINTS - REMOVAL/INSTALLATION
__________________________________________________________
 1.  General
_______
 A.  This procedure has two tasks. The first task gives instructions to remove the retractable center guide/restraints. The second task gives instructions to install the center guide/restraints. This procedure also gives instructions to remove and install these components from the center guide/restraints: the push-down fittings, the casters, and the rollers.
 NOTE: The center guide/restraints in the area of the side cargo door do
____
 not have casters or rollers.

 TASK 25-58-05-004-001
 2.  Retractable Center Guide/Restraints Removal (Fig. 401)
___________________________________________
 A.  Access
 (1)  Location Zone
 210 Main Deck

 B.  Remove the Center Guide/Restraints
 S 034-034
 (1)  Lift and turn (horizontally) the shear-plunger levers to retract the shear-plunger studs from the holes in the seat tracks.
 NOTE: The shear-plunger levers must stay locked in the up position.
____
 S 034-019
 (2)  
Move each tension bar forward or aft to align the tension bar studs with the holes in the seat tracks.

 S 024-020

 (3)  
Remove the center guide/restraint.

 C.  Remove the Push-Down Fittings
 S 024-027
 (1)  For the center guide/restraints with casters or rollers, do these steps:
 (a)  Push the release-lever on the side of the beam assembly to extend the push-down fitting.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-58-05
 ALL  ú ú 07 Page 401 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SHAFT 
VERTICAL RESTRAINT 
LIP (SWIVELING) 
PUSH-DOWN 
PLUNGER  SPRING  FITTING 
RELEASE 
LEVER 
VERTICAL RESTRAINT  SHEAR PLUNGER 
LIP (SWIVELING)  STUD 
SCREW AND WASHER 
LOCATING PIN  ASSEMBLY BEAM  (EACH SIDE) 
RETRACTABLE 
CENTER GUIDE 

BOLT, WASHER AND NUT (6 LOCATIONS PER CASTER OR ROLLER)
CASTER
1 (2 LOCATIONS)
TENSION BAR STUD RELEASE LEVER
SHEAR PLUNGER HANDLE
LOCKPLUNGER
CENTER GUIDE/RESTRAINT WITH CASTERS OR ROLLERS (EXAMPLE)
PUSH-DOWN FITTING HANDLE
SHEAR
SPACER
PLUNGER HANDLE
PIN
(EACH SIDE)

BEAM ASSEMBLY LOCATING
BOLT, WASHER
PIN
AND NUT
RETRACTABLE CENTER GUIDE LOCKPLUNGER
TENSION
RELEASE
BAR STUD
LEVER
SPRING
SHEAR PLUNGER STUD CENTER GUIDE/RESTRAINT (EXAMPLE)
1 SOME UNITS HAVE ROLLERS IN PLACE OF CASTERS Retractable Center Guide/Restraints Installation Figure 401
C76762
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-58-05
 ALL  ú ú 04 Page 402 ú Oct 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Remove the screws and washers which attach the shaft to each side of the beam assembly.

 (c)  
Remove the shaft and the spring from the push-down fitting and the beam assembly.

 (d)  
Remove the push-down fitting.

 S 024-032
 (2)  For the center guide/restraints without casters or rollers, do these steps:
 (a)  
Push the release-lever on the side of the beam assembly to extend the push-down fitting.

 (b)  
Remove the nut, washer, bolt, and spacers which attach the push-down fitting to the beam assembly.

 (c)  
Lift the handle below the push-down fitting to retract the pins from each side of the beam assembly.

 (d)  
Remove the push-down fitting.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS 2(128)