(a)  
The chute assembly engages the chute lock.

 (b)  
The inflation cable moves at least 0.85 inches.

 G. Put the airplane back to its normal condition.
 S 985-026-002
 (1)  Put the escape slide in its usual position as follows:
 (a)  
See that the manual release handle is in the UNLOCKED position.

 (b)  
Put the chute back to its normal position.

 S 865-031-002
 (2)  
Close the upper deck door.

 S 865-027-002

 (3)  
Return the escape slide to a serviceable condition.

 (a)  
Connect the gas supply hose.

 (b)  
Attach the release lanyards (two) and install the cotter pins.

 (c)  
Remove the stored gas bottle simulator (or the expended bottle) and install a serviceable stored gas bottle (AMM 25-68-04/201).

 S 865-028-002
 (4)  Return the escape slide assembly to its usual position.
 (a)  Unlock the assembly from the tracks.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-68-00
 ALL  ú CONFIG 2 ú 02 Page 510 ú Feb 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (b) (c)  Move the assembly aft to its normal position.Lock the assembly to the tracks.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-68-00
 ALL  ú CONFIG 2 ú 02 Page 511 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 FLOOR MOUNTED ESCAPE SLIDE UNIT - REMOVAL/INSTALLATION
______________________________________________________
 1.  General_______
 A.  The floor-mounted escape slide may be removed and installed as a complete unit including the escape slide pack and packboard, the stored gas bottle, and the base and chute assembly. Removal of the complete unit is accomplished by unlatching the base shear plunger, removing the stop from the forward end of the inboard track, moving the unit forward or aft (approximately 0.90 inch) and lifting it up clear of the floor tracks. However, because the escape slide pack weighs approximately 167 pounds and the stored gas bottle approximately 45 pounds, it is recommended that the assembly be removed in three stages: the stored gas bottle, the escape slide pack, and the base and chute assembly.
 B.  This procedure contains two tasks:
 (1)
A task to remove the escape slide assembly

 (2)
A task to install the escape slide assembly.

 TASK 25-68-02-004-001
 2.  Remove the Floor Mounted Escape Slide Assembly______________________________________________
 A.  Special Tools and Equipment
 (1) Crew Service Door Safety Barrier - 6PRE65B00040
 B.  References
 (1) AMM 25-68-04/201, Stored Gas Bottle
 C.  Access
 (1)  
Location Zone
 224 Fwd Upper Deck, RH

 (2)  
Access Panel
 849R Upper Deck Emergency Door, RH

 D.  Prepare To Remove the Escape Slide.
 S 494-002
 (1)
Put a maintenance stand outside the of the upper deck door.

 (2)
Open the upper deck door.

 (3)
Install the safety barrier at the door.

 S 984-005

 (4)
Put the escape slide in position adjacent to the door.

 (a)
Unlock the slide assembly from the tracks.

 (b)
Move the assembly forward to put it adjacent to the door.

 (c)
Lock the assembly to the tracks.

 S 864-003
 S 494-004
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 25-68-02
 ALL  ú ú 02 Page 401 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS 2(168)