(a)
Make sure that the flaps are controlled by alternate control.
(b)
Turn the ALTN FLAPS switch to put the flaps in the specified position.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-04
ALL ú ú 01 Page 512 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(c) Turn the ALTN FLAPS switch to OFF.
S 225-019
(3) Make sure that the clearance between the outboard end of the foreflap and the midflap support track is a minimum of 1 inch
(2.5 cm) (View C, Fig. 501).
S 825-020
(4)
Adjust the shim thickness between the support track and structure to keep the correct clearance.
J.
Examine the Adjustment of the Ball Screw Upstop
S 865-021
(1) Pressurize hydraulic system No. 4 (AMM 29-11-00/201).
S 865-066
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
CAUTION:_______MONITOR THE FLAP MOVEMENT CAREFULLY. THE FLAPS CAN BE DAMAGED BY INCORRECTLY ADJUSTED COMPONENTS.
DO NOT OPERATE THE FLAP IF THE AFTFLAP IS NOT CONNECTED TO THE MIDFLAP. THE AFTFLAP AND THE MIDFLAP WILL BE DAMAGED. BEFORE YOU OPERATE THE FLAPS, MAKE SURE THAT THE HOOK ON THE GENEVA CAM MECHANISM IS IN THE RELEASED POSITION (DETAIL B, FIG. 502). THE FLAPS WILL BE DAMAGED IF YOU OPERATE THEM WITH THE HOOKS IN THE LATCHED POSITION.
(2) Push the ALTN FLAPS ARM switch to put the flap control system in normal control.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-04
ALL ú ú 01 Page 513 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 865-022
(3) Put the flap control lever in the UP detent to retract the flaps.
NOTE: Control the hydraulic pressure to retract the flaps slowly.
____
S 225-023
(4) Make sure that the distance, called Dimension X, between the universal joint and the ball screw nut (View A, Fig. 501) is 0.45 to
0.74 inch (1.14 to 1.88 cm).
K. If the Ball Screw Nut Clearance is Out of the Tolerance, Adjust the Ball Screws
S 865-024
(1)
Release the pressure in hydraulic system No. 4 (AMM 29-11-00/201).
S 835-025
(2)
Adjust the ball screws:
(a)
Disconnect the torque tubes at the transmissions. 1) Remove the three screws which connect the spline coupling
sleeve to the torque tube. 2) Move the coupling sleeve off the torque tube.
(b)
Use the manual drive tool to turn the transmission coupler until the ball screw nut touches the universal joint stop.
(c)
Turn the coupler, one full turn plus 24 teeth away from the stops.
(d)
Make sure that the clearance between the universal joint and the ball screw nut stops is 1/2 turn (0.59 inch (1.50 cm)).
(e)
Install the torque tubes: 1) Align the splines of the coupling sleeves. 2) Move the coupling sleeve on the torque tube. 3) Install the three screws which connect the sleeve to the
torque tube.
CAUTION: MAKE SURE YOU INSTALL LOCKWIRE ON THE COUPLING
_______ SCREWS. IF THE COUPLING SCREWS COME OFF, THE TORQUE TUBE COUPLING WILL DISCONNECT AND CAUSE DAMAGE TO THE AIRPLANE.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(107)
