27-51-17
ALL ú ú 01 Page 408 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(2)
AMM 20-11-14/701, Metal Surfaces
(3)
AMM 24-22-00/201, Manual Control
(4)
AMM 27-51-17/501, Flap Alternate Drive Motor
(5)
AMM 29-11-00/201, Main Hydraulic Supply System
(6)
AMM 32-00-30/201, Landing Gear Door Locks
D.
Access
(1)
Location Zone
138 Body Landing Gear Wheel Well, RH
E.
Procedure
S 144-012
(1)
Clean the surfaces of the motor and the power package for an electrical bond (AMM 20-11-14/701).
S 614-024
(2)
For outboard drive motor part number 793T100, do this task: "Trailing Edge Flap Drive System Servicing" (AMM 12-13-13/301).
NOTE: It is not necessary to service the S256T004-15 alternate
____
drive motor.
S 424-013
(3)
Install the outboard drive motor:
(a)
Apply a thin layer of grease to the output spline of the motor.
(b)
Remove the cover from the power package.
(c)
Apply a thin layer of grease to the power package input spline.
(d)
Put the motor (5) on the power package.
(e)
Attach the motor to the power package with bolts (2, 3 and 7), washers (1), and a nut (4).
(f)
Install the lockwire on the bolts.
S 374-014
(4) Apply a layer of primer to the line between the motor and the power package.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-17
ALL ú ú 01 Page 409 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 434-015
(5)
Connect the electrical connector (6) to the motor.
F.
Put the Airplane Back to Its Usual Condition
S 864-037
(1)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P6, Main Power Distribution Panel
1) 6L19, TE FLAP ELEC CONT OTBD
(b)
P415, Power Distribution Panel
1) 415M38, TE FLAP ELEC OTBD
S 864-039
(2) Do this task: "Supply Electrical Power" (AMM 24-22-00/201).
S 714-028
CAUTION: DO NOT OPERATE THE TRAILING EDGE FLAPS WITH ELECTRICAL POWER
_______ THROUGH MORE THAN ONE FULL EXTEND/RETRACT CYCLE IN A 25 MINUTE TIME. THERE WILL BE DAMAGE TO THE FLAP ELECTRIC MOTORS IF YOU OPERATE THEM TOO FREQUENTLY.
(3)
Do a test of the flap alternate drive motor.
(a)
Push the ALTN FLAPS ARM switch to arm the alternate flap control system.
(b)
Turn the ALTN FLAPS switch to the EXT position. Make sure that the flaps extend.
(c)
Stop for 5 minutes to let the electric drive motors become cool.
(d)
Turn the ALTN FLAPS switch to the RET position. Make sure that the flaps retract.
(e)
Turn the ALTN FLAPS switch to the OFF position.
WARNING: MAKE SURE ALL PERSONS AND EQUIPMENT ARE CLEAR OF THE LE
_______ AND TE FLAPS AND FLAP DRIVE MECHANISMS. THE TE AND LE FLAPS WILL MOVE TO AGREE WITH THE CONTROL LEVER POSITION WHEN ALTERNATE CONTROL IS DISARMED. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(f) Push the ALTN FLAPS ARM switch to disarm the alternate flap control.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-17
ALL ú ú 03 Page 410 ú Jun 18/01
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊(cè) 飛行操縱 FLIGHT CONTROLS 4(161)
