(4)  
Make sure that the clearance between the spoilers and the midflap is a minimum of 0.09 |0.07 inch (0.23 |0.18 cm)(View A-A Fig. 501).

 S 835-039

 (5)  
If the clearance is out of the tolerance, adjust the spoilers (AMM 27-61-00/501).

 O.
Do a Check of the Aftflap Adjustment

 S 865-040
 (1)  
Put the speedbrake control lever in the UP detent to lift the spoilers No. 1-4 and 9-12 above the outboard flaps.

 S 495-041

 (2)  
Install the spoiler actuator locking tools or move the FLT CONTROL HYD POWER switches to SHUTOFF to make sure the spoilers will not retract.

 S 865-042

 (3)  
Release the pressure in hydraulic systems No. 2 and 3
 (AMM 29-11-00/201).

 (4)  
Install the movable flap track fairings (AMM 27-51-31/401).

 S 435-044
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-04
 ALL  ú ú 03 Page 519 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 865-045
 (5)  Pressurize hydraulic system No. 4 (AMM 29-11-00/201).
 S 865-085
 CAUTION:_______MONITOR THE FLAPS CAREFULLY WHILE THEY RETRACT. THE FLAPS CAN BE DAMAGED BECAUSE OF INCORRECTLY ADJUSTED COMPONENTS.
 (6)  
Put the flap control lever in the UP detent to retract the flaps.

 S 865-047

 (7)  
Release the pressure in hydraulic system No. 4 (AMM 29-11-00/201).

 S 835-086

 (8)  
Do a check of the aftflaps adjustment with the flap track movable fairing bulb seals compressed.

 NOTE: The flaps must be in the fully retracted position.
____ You must extend the flaps for access, if adjustment of these dimensions is necessary.
 CAUTION:_______ADJUST THE AFTFLAP ACTUATOR RODS (AFT RODS) ONLY. THE NECESSARY DIMENSION MUST BE IN THE LIMITS AT THE TWO ENDS OF THE FLAP TO PREVENT FLAP DAMAGE.
 THE PUSHRODS (FORWARD RODS) MUST BE KEPT AT THE LENGTH SHOWN IN DETAIL A, FIG. 502 TO PREVENT ROD LOADS THAT ARE TOO HIGH. THE PUSHRODS CAN BE DIFFERENT FROM THE SPECIFIED LENGTH ONLY WHEN THE ACTUATOR RODS CANNOT BE ADJUSTED TO THE 6.70-6.80 INCH (17.0-17.3 CM) DIMENSION. IF THE LENGTH OF THE PUSHRODS IS CHANGED, IT MUST BE THE SAME ON THE TWO PUSHRODS.
 (a)  
Make sure that the dimension between the aftflap and the midflap is 6.70-6.80 inches (17.0-17.3 cm) (View B-B, Fig. 501).

 (b)  
Make sure that the seal between the midflap and the aftflap is adjusted to the limits shown (View B-B, Fig. 501).

 (c)  
Make sure that the clearance between the aftflap and the support strut is a minimum of 0.22 inch (0.56 cm) (View B-B, Fig. 501).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-04
 ALL  ú ú 03 Page 520 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

INCH
0.05  TRAILING EDGE INBD

A-A
Outboard Flap Adjustment
Figure 503

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-04
 ALL  ú ú 01 Page 521 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
G53158
 (d)

(e)

(f)

A
747-400 MAINTENANCE MANUAL
Make sure that the clearance between the midflap trailing edge
 and the aftflap is 0.22-0.27 inch (0.56-0.69 cm)
 (View B-B, Fig. 501):
 1)  Pressurize hydraulic systems No. 2, 3 and 4 (AMM 29-11-00/201).
 2)  Put the flap control lever in the 30-unit detent to extend the flaps.
 3)  Examine the leading edge of the aftflap for damage.
 4)  If the leading edge has damage, make sure that the fastener threads on the cove panel support extend 0.11 inch
 (0.28
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(110)