EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-01
ALL ú ú 01 Page 602 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
3. BEARING/TRACK
(0.57-0.66 cm)
Inboard Foreflap Track and Midflap Roller Wear Limits
Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-01
ALL ú ú 01 Page 603 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
INDEX 1 NO. OD ID BUSHING ROLLER PART NAME DIM. (cm)(cm) DESIGN LIMITS (1.412) (1.417) 0.55800.5560 (1.422) (1.425) 0.56100.5600 MINIMUM INCHES INCHES MAXIMUM DIAMETER (cm) WEAR LIMITS (1.397) 0.5500 INCHES DIMENSION WEAR PERMITTED 1 (0.025) 0.010 (cm) INCHES CLEARANCE DIAMETER MAXIMUM X REPLACE WORN PART INSTR REPAIRREPAIR WORN PART
X
2 TRACK X XROLLER (5.08)(5.03) 1.980 2.000 (0.660) 0.260 (0.648) 0.255 (4.593) 1.950 (0.572) 0.225 1 2 X
X
3 TRACK BEARING OD 5 (7.607) 2.995 (7.633) 3.005 (6.033) 2.375 (6.030) 2.374 4 3 X
X
IF THE TEFLON LINER IS TORN OR WORN, THE ROLLER MUST BE REPLACED
YOU CAN ADD A 63B11367-5 SHIM WASHER BETWEEN THE ROLLER AND BUSHING IN THE RIB ON THE MIDFLAP TO KEEP THE 0.014-0.064 INCH (0.04-0.16 cm) DIMENSION BETWEEN TRACK AND ROLLER AND 0.25 INCH (0.64 cm) SIDE MOVEMENT OF THE TRACK AT FLAP LEADING EDGE. EXAMINE THE SIDE MOVEMENT, WITH THE TRACK EXTENDED 10 TO 12 INCHES FROM THE MIDFLAP LEADING EDGE WHILE YOU APPLY HAND PRESSURE TO ENGAGE THE TRACK IN BOTH SETS OF ROLLERS. THE CHROME PLATING ON THE TRACK EDGE SURFACE THAT TOUCHES THE ROLLER SHOULD NOT BE WORN THROUGH TO THE BASE METAL
THE DESIGN CLEARANCE BETWEEN THE TRACK AND ROLLER IS A FUNCTION OF THE DISTANCE BETWEEN THE UPPER AND LOWER ROLLERS AND TRACK HEIGHT. THE CLEARANCE ALSO CHANGES WITH DIFFERENT CONDITIONS OF TRACK EXTENSION. THE WEAR LIMITS ARE PRESENTED IN TERMS OF WORN ROLLER DIAMETER AND WORN TRACK HEIGHT
THE BEARING OR ROLLER INDENTATION WEAR ON THE FOREFLAP TRACK MUST NOT BE MORE THAN
0.02 INCH (0.05 cm)
THE HEIGHT OF THE TRACK
Inboard Foreflap Track and Midflap Roller Wear Limits
Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-01
ALL ú
ú 01 Page 604
ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
A-A
1 INDEX NO. ARM BUSHING PART NAME DIM. ID OD 1.2677 (3.220) (3.226) (3.219) (3.197) 1.2672 1.27001.2685 DIAMETER MAXIMUM INCHESINCHES MINIMUM (cm) (cm) DESIGN LIMITS (3.203) (3.239) 1.275 1.261 PERMITTED WEAR DIMENSION INCHES (cm) WEAR LIMITS (0.018) 0.007 MAXIMUM DIAMETER CLEARANCE INCHES (cm) X PART WORN REPLACE REPAIR INSTR PART WORN REPAIR
X
2 ODARM BUSHING 1 (12.802) (0.239) 5.040 0.094 (12.776) (0.226) 0.089 5.030 (0.213) 0.084 2 0.050 (0.130) X
X
BUSHING FLANGE THICKNESS THE PLATING MUST NOT BE WORN THROUGH
Inboard Aftflap Arm Assembly Wear Limits Figure 602
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-01
ALL ú
ú 01 Page 605
ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
INBOARD FOREFLAP - REMOVAL/INSTALLATION
_______________________________________
1. General_______
A. This procedure contains two tasks. The removal and the installation of an inboard foreflap.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(84)
