(2)  
Micrometer - 1 to 2 inch (2 to 5cm), inside measuring

 (3)  
Micrometer - 1 to 2 inch (2 to 5cm), outside measuring

 (4)  
Vernier Caliper

 (5)  
Dial Indicator

 B.  
References

 (1)  
27-51-03/401, Aftflap - Inboard

 C.  
Access

 (1)  
Location Zone
 578 Inboard Flap Aftflap, LH
 678 Inboard Flap Aftflap, RH

 D.  
Procedure

 S 026-002
 (1)  
Remove the inboard aftflap (Ref 27-51-03/401).

 S 226-003

 (2)  
Measure the parts which connect the inboard aftflap for worn areas.

 (a)  
Remove the parts.

 (b)  
Use a micrometer or a vernier caliper to measure the parts.

 (c)  
Compare the dimensions that you measured with the permitted dimensions shown in Fig. 601.

 (d)  
Repair or replace the parts that are not in the tolerance as shown in Fig. 601.

 (e)  
Install the parts.

 S 226-004
 (3)  
Measure the axial play in the inboard aftflap bearing.

 (a)
Disconnect the parts to examine the axial play.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-03
 ALL  ú ú 01 Page 601 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Attach a dial indicator.

 (c)  
Measure the axial play.

 (d)  
Compare the axial play which you measured to the permitted axial play as shown in Fig. 601.

 (e)  
Replace the bearings which are not in the tolerance.

 (f)  
Connect the items which you disconnected.

 S 426-005
 (4)  Install the inboard aftflap (Ref 27-51-03/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-03
 ALL  ú ú 01 Page 602 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

MIDFLAP  FWD  A  A  AFTFLAP 
1. BUSHING/PIN  7. BOLT  2. BUSHING/ SPINDLE  3. BEARING 
6. BUSHING/PIN  5. BEARING/ A-A (4 LOCATIONS) SPINDLE  4. BEARING 
Inboard Aftflap Wear Limits Figure 601 (Sheet 1) 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-03
 ALL  ú ú 01 Page 603 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

1 INDEX NO.  PIN BUSHING PART NAME DIM. ID OD  (cm)(cm) MAXIMUMMINIMUM 1.1862 1.1867 1.1875 1.1880 INCHES INCHES DESIGN LIMITS DIAMETER (3.014)(3.013) (3.018)(3.016)  (cm) DIMENSION 1.1807 1.1935 PERMITTED INCHES WEAR WEAR LIMITS (2.999) (3.031)  (cm) CLEARANCE 0.0068 MAXIMUM DIAMETER INCHES (0.017)  PART WORN REPLACE X X  PART WORN REPAIR  REPAIR INSTR 
2  SPINDLE BUSHING ---- (6.629)(6.617) (0.239)(0.226) 2.6102.605 0.0940.089 2 2 1 1  (0.201) 0.079 3 1  (AXIAL) 0.032 (0.081)  X  X  4 
3  BEARING ID ODX  XX  X  0.010 5 (0.025)  X 
4  BEARING OD ID X  XX  X  0.010 5 (0.025)  X 
5  SPINDLE BEARING ID OD  2.249 2.251 2.253 2.256 (5.718)(5.712) (5.730)(5.723)  2.261 3 (5.743)  0.010 (0.025)  X  X  4 
6  BUSHING PIN ID OD  1.1875 1.1880 1.18671.1862 (3.014)(3.013) (3.018)(3.016)  1.192 1.181 (2.300) (3.028)  0.005 (0.013)  X X 
7  BOLT ID OD X  (0.632) (0.634) 0.24950.2490 XX  (0.584) 0.230 X  X  6 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(94)