S 862-030
(3)
Release the pressure in hydraulic systems No. 1 and No. 4 (AMM 29-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-10
ALL ú ú 01 Page 210 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 862-031
(4)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6, Main Power Distribution Panel
1) 6L20, TE FLAP ELEC CONT INBD
2) 6L19, TE FLAP ELEC CONT OTBD
D.
Remove the Bypass Valve Motor
S 032-089
(1)
Disconnect the electrical connectors (3) from the valve motor (1).
(a)
DM625 (Alternate Inboard Flap Motor)
(b)
DM622 (Alternate Outboard Flap Motor)
S 022-090
(2)
Remove the bypass valve motor:
(a)
Move the manual override lever (27) to position 2.
(b)
Remove the four screws (30) from the bypass valve motor (1).
(c)
Remove the bypass valve motor.
(d)
Keep a record of the part number and serial number of the removed motor.
TASK 27-51-10-402-033
7. Flap Control Bypass Valve Motor Installation____________________________________________
A. References
(1)
AMM 24-22-00/201, Manual Control
(2)
AMM 29-11-00/201, Main Hydraulic Supply System
B.
Access
(1)
Location Zone
137 Body Landing Gear Well, LH
138 Body Landing Gear Well, RH
C.
Procedure
S 422-034
(1)
Install the bypass valve motor:
(a)
Transfer the part number and serial number of the removed motor to the data plate of the new motor.
(b)
Make sure that the manual override lever (27) is at position 2.
(c)
Put the bypass valve motor (1) on the valve (4). Engage the motor drive with the valve cam.
(d)
Install the four screws (30) and washers (31).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-10
ALL ú ú 01 Page 211 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(e) Install the lockwire on the screws.
S 432-091
(2)
Install the electrical connectors (3) on the valve motor (1).
(a)
DM625 (Alternate Inboard Flap Motor)
(b)
DM622 (Alternate Outboard Flap Motor)
S 862-035
(3)
Supply electrical power (AMM 24-22-00/201).
S 862-096
(4)
Pressurize hydraulic systems No. 1 or No. 4 (AMM 29-11-00/201).
S 862-092
(5)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P6, Main Power Distribution Panel
1) 6L20, TE FLAP ELEC CONT INBD
2) 6L19, TE FLAP ELEC CONT OTBD
S 712-093
(6)
Do a check of the bypass valve motor operation:
(a)
Push the ALTN FLAPS ARM switch on the pilot's center panel to put the flap system in alternate control.
(b)
Make sure that the bypass valve manual override lever moves to position 1.
(c)
Move the flap control lever. Make sure that the flaps do not move.
(d)
Move the flap control lever to the UP detent.
WARNING: THE TRAILING EDGE FLAPS WILL MOVE TO AGREE WITH THE
_______ CONTROL LEVER POSITION WHEN ALTERNATE CONTROL IS DISARMED. MAKE SURE THAT ALL PERSONS AND EQUIPMENT ARE CLEAR OF THE TE AND LE FLAPS.
(e)
Push ALTN FLAPS ARM switch to put the flaps in primary control.
(f)
Make sure that the bypass valve manual override lever moves to position 2.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(147)
