B.
References
(1)
27-51-05/401, Outboard Foreflap
C.
Access
(1)
Location Zone
586 Outboard Flap Foreflap, LH
686 Outboard Flap Foreflap, RH
D.
Procedure
S 026-002
(1)
Remove the foreflap (Ref 27-51-05/401).
S 226-003
(2)
Examine the parts, which connect the foreflap, for worn areas:
(a)
Remove the parts.
(b)
Measure the parts.
NOTE: Use a micrometer or a vernier caliper.
____
(c)
Compare the dimensions you measured, with the permitted dimensions shown in Fig. 601.
(d)
Replace the parts that are out of the tolerance.
(e)
Install the parts.
(3)
Install the foreflap (Ref 27-51-05/401).
S 426-004
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-05
ALL ú ú 01 Page 601 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
FOREFLAP
MIDFLAP
FWD
LEVER CARRIAGE
SEE B SEE A
CARRIAGE
FOREFLAP
SEQUENCE
CARRIAGE
FOREFLAP A
MIDFLAP TRACK
FLAP (4 LOCATIONS)
TRACK
MIDFLAP
A
B
LEVER
B
BOLT/NUT
B
A
Outboard Foreflap Wear Limits
Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-05
ALL ú ú 01 Page 602 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
1. BEARING/BOLT 2. BEARING BOLT
FOREFLAP FITTING
FOREFLAP FITTING
SEQUENCE CARRIAGE
SEQUENCE
CARRIAGE
INBOARD FLAP TRACK OUTBOARD FLAP TRACK A-A
NO. 1 INDEX PART NAME DIM. IDBEARING INCHES MINIMUM MAXIMUM INCHES DESIGN LIMITS DIAMETER (cm) (cm) 0.50000.4995 (1.269) (1.270) 0.5045 PERMITTED DIMENSION INCHES WEAR WEAR LIMITS (cm) (1.281) 0.0050 MAXIMUM DIAMETER CLEARANCE INCHES (cm) PART WORN REPLACE X REPAIR INSTRPART WORN REPAIR
ODBOLT 0.49950.4990 (1.267) (1.269) 0.4950 (1.257) (0.013) X
2 ID OD BEARING BOLT 0.3745 0.3750 0.3740 0.3745 (0.951) (0.953) (0.950) (0.951) 0.3700 0.3795 (0.964) (0.940) 0.0050 (0.013) X
X
Outboard Foreflap Wear Limits
Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-05
ALL ú ú 01 Page 603 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
OLD CONFIGURATION NEW CONFIGURATION
B-B
Outboard Foreflap Wear Limits
Figure 601 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-05
ALL ú ú 01 Page 604 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H40477
A
747-400
MAINTENANCE MANUAL
2 1 NO. INDEX PART NAME DIM. OD IDBUSHING BUSHING (cm)(cm) DIAMETER DESIGN LIMITS INCHES MAXIMUMMINIMUM INCHES 0.5605 0.5630 0.5595 0.5615 (1.424)(1.421) (1.430)(1.426) (cm) WEAR LIMITS WEAR INCHES DIMENSION PERMITTED 0.555 0.568 (1.410) (1.443) (cm) INCHES CLEARANCE DIAMETER MAXIMUM 0.007 (0.018) REPLACE WORN PART REPAIR WORN INSTR REPAIR PART X X 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(119)
