(3)
32-00-30/201, Landing Gear Door Locks
(4)
IPC 27-51-60, Fig. 1
B.
Access
(1)
Location Zone 135 Wing Landing Gear Wheel Well, LH 136 Wing Landing Gear Wheel Well, RH 572 Landing Gear Support Beam and Rear Spar to Trailing Edge,
LH 672 Landing Gear Support Beam and Rear Spar to Trailing Edge,
RH 581 Rear Spar to Trailing Edge, LH 681 Rear Spar to Trailing Edge, RH
C. Prepare to Remove a Flap Angle Gearbox
S 864-004
(1) Make sure that the landing gear ground locks are installed.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-21
ALL ú ú 01 Page 401 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 494-005
WARNING: CAREFULLY DO THE SPECIFIED TASK TO INSTALL THE DOOR LOCKS FOR
_______ THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(2)
Install the door locks on the doors for the body landing gear (Ref 32-00-30/201).
S 864-002
(3)
Pressurize hydraulic systems No. 1 and 4 (Ref 29-11-00/201).
S 864-017
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
(4)
Put the flap control lever in the 30-unit detent to extend the flaps.
S 864-006
(5)
Release the pressure in hydraulic systems No. 1 and 4 (Ref 29-11-00/201).
D.
Remove A Flap Angle Gearbox
S 034-007
(1)
Disconnect the torque tube ends on the two sides of the angle gearbox.
(a)
Remove the three screws which connect the coupling sleeve to the torque tube.
(b)
Move the coupling sleeve to the gearbox.
S 024-008
(2) Remove the bolts and remove the gearbox from the airplane.
NOTE: If you will install the same gearbox, keep and identify,
____ or measure the thickness of the shims on the bolts. This will be necessary when you install the gearbox.
TASK 27-51-21-404-009
3. Flap Angle Gearbox Installation (Fig. 401)
_______________________________
A. Consumable Materials
(1)
D00633 Grease - BMS 3-33 (recommended)
(2)
D00013 Grease - MIL-G-23827 (alternative)
(3)
C00259 Enamel - Primer, Green, BMS 10-11
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-21
ALL ú ú 01 Page 402 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE A
FWD
TORQUE TUBE
ANGLE GEARBOX (EXAMPLE 8 L0CATIONS)
BSEE (3 LOCATIONS) SCREW INBOARD FLAP CONTROL UNIT SPLINE A TORQUE TUBE OUTBOARD FLAP CONTROL UNIT
SPLINE COUPLING SLEEVE
B BOLT (EXAMPLE)
Flap Angle Gearbox Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-21
ALL ú ú 01 Page 403 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
B. References
(1)
27-51-20/401, Flap Torque Tube
(2)
29-11-00/201, Main Hydraulic Supply System
(3)
32-00-30/201, Landing Gear Door Locks
(4)
IPC 27-51-60, Fig. 2
C.
Access
(1)
Location Zone 135 Wing Landing Gear Wheel Well, LH 136 Wing Landing Gear Wheel Well, RH 572 Landing Gear Support Beam and Rear Spar to Trailing Edge,
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(181)
