PUSHRODS.
(f)
Align the actuator rods (12) with the aftflap fittings.
(g)
Adjust the rod ends.
(h)
Make sure that you can see the rod ends threads through the inspection hole.
(i)
Tighten the checknuts on the rod ends.
(j)
Install the lockwire on the checknuts.
S 434-016
CAUTION: BEFORE THE ACTUATOR RODS ARE CONNECTED, MAKE SURE THAT THE HOOK
_______ ON THE GENEVA CAM MECHANISM IS IN THE RELEASED POSITION AS SHOWN ON FIG. 402. THE FLAPS WILL BE DAMAGED IF THEY ARE MOVED WITH THE HOOKS IN THE LATCHED POSITION.
(6)
Install the rod ends on the aftflap with a bolt (14), bushing (8), washers (9, 11 and 13), and a nut (10).
(a)
Tighten the nut to 120 pound-inches (14 N-m). Continue to tighten the nut until the cotter pin hole is aligned.
NOTE: Install the washer between the clamp-up bushing and the
____ bearing to make sure the flanged bushing will not move.
(b) Install the cotter pin.
S 864-028
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
(7) Move the flap control lever to the position of the flaps.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-06
ALL ú ú 01 Page 412 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 864-018
WARNING: THE TRAILING EDGE AND THE LEADING EDGE FLAPS WILL MOVE TO AGREE
_______ WITH THE CONTROL LEVER POSITION WHEN THE ALTERNATE CONTROL IS DISARMED. MAKE SURE THAT ALL PERSONS AND EQUIPMENT ARE OUT OF THE PATH OF THE FLAPS.
(8)
Push the ALTN FLAPS ARM switch to disarm the alternate control.
I.
Adjust the Aftflap
S 864-019
(1)
Pressurize hydraulic system No. 4 (Ref 29-11-00/201).
S 714-020
(2)
Move the flaps slowly.
NOTE: Make sure the flaps move freely.
____
S 864-030
(3)
Retract the flaps.
S 224-021
(4)
Make sure that the clearance between the midflap trailing edge and the top surface of the aftflap is in the tolerance of Detail A, Fig. 404.
(a)
Add or remove shims at the bottom forward end of the support strut to adjust the clearance: 1) Loosen the nut on the bolt in the top aft end of the
support strut. 2) Remove the bolt from the bottom forward end of the support
strut. 3) Add or remove shims if it is necessary. 4) Apply a layer of wet primer on the shims. 5) Install the shims, filler, concave and convex washers, and
the bolt. 6) Tighten the bolt. 7) Tighten the nut on the bolt in the top aft end of the
support strut.
(b)
After the adjustment, make sure that the screws will not touch the aftflap in the fully retracted position.
J.
Put the Airplane Back to its Usual Condition.
(1)
Move the flaps slowly. Make sure that the flaps move smoothly.
(2)
Lubricate the aftflap (Ref 12-21-20/301).
S 714-022
S 644-023
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-06
ALL ú ú 01 Page 413 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(3) S 864-024Release the pressure in hydraulic system No. 4 (Ref 29-11-00/201).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(124)
