(2)
AMM 24-22-00/201, Manual Control

 (3)
AMM 27-51-09/501, Flap Power Package

 (4)
AMM 27-51-18/401, Limit Switch Pack

 (5)
AMM 27-58-01/401, Flap Position Transmitter

 (6)
AMM 29-11-00/201, Main Hydraulic Supply System

 (7)
AMM 32-00-30/201, Landing Gear Door Locks

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-09
 ALL  ú ú 01 Page 410 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 E. Access
 (1)  
Location Zone
 137 Body Landing Gear Well, LH
 138 Body Landing Gear Well, RH

 F.
Procedure

 S 704-033
 (1)  
Make sure that the power package output shafts move smoothly.

 S 434-034

 (2)  
Install the adapters (14) in the flap control module (7):

 (a)  
Remove the caps from the flap control module ports.

 (b)  
Lubricate the rings (16) and the packings (15 and 17) with hydraulic fluid or Skydrol assembly lube.

 (c)  
Make sure that the flap control module (7) and hydraulic motor are filled with hydraulic fluid.

 (d)  
Install the rings (16), packings (15 and 17) and adapters (14) in the ports.

 S 424-035
 (3)  
Install the flap power package:

 (a)  
Put the bushings (18 and 23) in the mounting lugs (Fig. 401).

 (b)  
Attach the fishpole hoist to the lift point on the wheel well bulkhead.

 (c)  
Attach the hoisting adapter tool to the lift lugs on the flap power package (1).

 (d)  
Lift the flap power package (1) into its position.

 (e)  
Install the three bolts (21), washers (19 and 22) and the locknuts (20) (Detail B, Fig. 401).

 (f)  
Install the three bolts (21), washers (19 and 22) and nuts (20) (section A-A).

 (g)  
Align the input arm (2) with the rod (6).

 (h)  
Attach the input arm (2) with a bolt (3), washer (4) and nut (5).

 (i)  
Remove the fishpole hoist and hoisting adapter.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-09
 ALL  ú ú 01 Page 411 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 434-036
 (4)  
Connect the hydraulic lines (10):

 (a)  
Make sure hydraulic systems No. 1 and 4 are not pressurized.

 (b)  
Remove the plugs from the hydraulic lines.

 (c)  
Align the hydraulic lines with the ports in the flap control module (7).

 (d)  
Tighten the nuts on the hydraulic lines (10).

 S 434-037
 (5)  
Connect the electrical connectors:

 (a)  
DV138 (Inboard Flap By-Pass Valve)

 (b)  
DV139 (Outboard Flap By-Pass Valve)

 (c)  
DM625 (Alternate Inboard Flap Motor)

 (d)  
DM622 (Alternate Outboard Flap Motor)

 S 434-038
 (6)  
Connect the bonding jumpers to the flap power package:

 (a)  
Connect the bonding jumper (23) to the alternate electric motor (24).

 (b)  
Connect the bonding jumper (8) between the bypass valve and the flap lever and quadrant assembly.

 S 434-018
 CAUTION:_______MAKE SURE THAT THE FLAPS ARE FULLY RETRACTED. THE RVDT CANNOT BE ADJUSTED IF THE FLAPS ARE EXTENDED.
 (7)  
Connect the electrical connector to the applicable RVDT (11) (AMM 27-58-01/401):

 (a)  
DM7889 Inboard Power Pack Transmitter

 (b)  
DM7892 Outboard Power Pack Transmitter

 S 434-019
 (8)  
Connect the electrical connector to the applicable limit switch pack (12) (AMM 27-51-18/401):
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(135)