(b)  
Push the two brake pedals fully until the stops limit the travel of the brake pedal, and hold the pedals in this position.

 (c)  
Put a 0.22 to 0.25-inch shim between the parking brake pawl and the pawl stops on the bellcrank.

 (d)  
Slowly pull on the parking brake handle until the parking brake pawl touches the shim and hold it in this position.

 (e)  
Do a check for continuity between the C and the NO terminals.

 NOTE: The electrical wires must be disconnected when you do a
____
 continuity check.

 (f)  If there no is continuity, bend the tab on the switch actuator until there is continuity.
 NOTE: When the switch adjustment is correct, the switch will
____ operate to the closed position when the pawl lobe on the parking brake pawl is between 0.22 and 0.25 inch from the pawl stop on the bellcrank as shown in detail D.
 (g)  
Remove the rig pins.

 (h)  
Push the brake pedals to release the parking brake.

 (i)  
Remove the 0.22 to 0.25-inch shim.

 (j)  
Do a check for continuity between the C and the NO terminals.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-44-00
 ALL  ú ú 01 Page 508 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (k)  If there is continuity, bend the tab on the switch actuator until there is no continuity.
 NOTE: Bend the tab away from the switch plunger to remove the
____ preload (a clearance of +0.005/-0.005 inch between the switch plunger and the switch actuator striker is permitted (detail H)).
 (l)  
Connect the electrical wires to the switch.

 (m)  
Push the two brake pedals fully until the stops limit the travel of the brake pedals and pull the parking brake handle.

 (n)  
Make sure the EICAS message PARKING BRAKE SET shows on the EICAS display.

 (o)  
If the EICAS message PARKING BRAKE SET does not show, then do the adjustment procedure again.

 (p)  
Push the two brake pedals to release the parking brake.

 (q)  
Make sure the EICAS message PARKING BRAKE SET does not show on the EICAS display.

 (r)  
If the EICAS message PARKING BRAKE SET shows, then do the adjustment procedure again.

 S 095-007
 (6)  Remove the rig pins from the rudder pedal arms.
 TASK 32-44-00-735-085
 3. System Test - Parking Brake System
__________________________________
 A. Standard Tools and Equipment
 (1)  
Pressure gage for use with BMS 3-11, Quantity 1, 0 to 4000 PSI pressure capacity

 B.
References

 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 12-15-09/301, Brake Hydraulic Accumulator

 (3)  
AMM 12-15-11/301, Hydraulic Pressure Surge Accumulator

 (4)  
AMM 24-22-00/201, Manual Control

 (5)  
AMM 29-11-00/201, Main Hydraulic Supply System

 (6)  
AMM 32-00-30/201, Landing Gear Ground Locks

 (7)  
AMM 45-10-00/201, Central Maintenance Computer System

 (8)  
WDM 31-51-17

 (9)  
WDM 32-44-11

 (10)
 AIPC 32-44-60 Fig. 1

 C.
Access

 (1)  
Location Zone
 221 Control Cabin, LH
 222 Control Cabin, RH
 735 Wing Landing Gear Left
 745 Wing Landing Gear Right
 755 Body Landing Gear Left
 765 Body Landing Gear Right

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-44-00
 ALL  ú ú 03 Page 509 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 D. Preconditions
 S 865-086
 (1)  
These preconditions are necessary for this task:

 (a)  
Electrical power is available (AMM 24-22-00/201).

 (b)  
Hydraulic systems are serviceable (AMM 29-11-00/201).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(109)