D.  
Examine the Wheels (Wheel Installed on the Airplane) Fig. 601.

 (1)
Examine the wheels for cracks, flaked paint and corrosion.

 S 216-004

 (2)  
Examine the wheel for signs of blistered paint and heat shield damage.

 S 216-003
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-03
 ALL  ú ú 07 Page 601 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

TIE BOLT
MEASURE DIAMETER OF EACH WHEEL HALF BETWEEN OUTER RIM SURFACES
ROTOR DRIVE KEY
HEAT SHIELD
Wheel Visual Inspection
Figure 601

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-03
 ALL  ú ú 01 Page 602 ú Oct 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (3)  S 286-029Examine the wheel for signs that it turned on a runway with no tire for one revolution or more. If you think this occurred, remove and discard the wheel.
 NOTE:____ Damage to the wheel that has rolled without a tire accrues very rapidly in the vertical portion of the rim flange (C section). Even though no physical damage (cracks, etc.), except for runway abrasions, is evident, the wheel flange is severely weakened. The probable failure mode of a wheel so damaged is a disintegrated rim flange; therefore no repair is authorize on wheels so damaged, no matter how minor the damage appears.
 (4)  S 216-006Make sure the hubcap is not loose. (a) Look for a loose clamp. 1) Tighten or replace the clamp if it is necessary.
 (5)  S 216-022Examine the tiebolt installations for: (a) Loose tiebolts and tiebolt nuts (b) Damaged tiebolts (c) Tiebolt locations that do not have tiebolts.
 (6)  S 026-023If you found a loose or damaged tiebolt or a tiebolt location without a tiebolt, remove the wheel (AMM 32-45-01/401 and AMM 32-45-02/401).
 (7)  S 216-037If you removed the wheel, do the steps to examine the wheel with the wheel removed from the airplane (Ref "Examine Wheels (Wheel Removed from Airplane)" paragraph).
 NOTE:____ Carefully examine the wheel for damage and broken parts.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-45-03
 ALL  ú ú 03 Page 603 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 216-035
 (8)  
If you removed a main wheel, examine the brake for:

 (a)  
Damage

 (b)  
Broken parts.

 S 436-009
 (9)
Make sure the rotor drive keys are tight (main wheels only).

 S 436-010

 (10)
 Tighten the nuts (refer to the applicable component maintenance manual for the torque).

 E.
Examine the Wheels (Wheel Removed from the Airplane)(Fig. 601).

 NOTE: See the applicable Component Maintenance Manual for all the wheel
____ and bearing inspection procedures.
 S 216-011
 (1)  
Examine metal parts of the wheel for cracks, scratches, stripped or cross-threaded parts, corrosion, worn plating or other damage.

 S 216-012

 (2)  
Examine the seal retainer for cracks, distortion or surface damage.

 S 216-013

 (3)  
Examine the bearing and bearing surfaces for distortion and flat spots.

 S 646-014

 (4)  
Make sure the bearing is sufficiently lubricated.

 S 216-015

 (5)  
Examine the preformed packing for cracks, distortion or surface damage.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(148)