(a)
P180 DC Power Distribution Panel
1) 180J25 AUTOBRAKE
S 024-005
(2)
Remove the autobrake control panel, P247, from the P8 control stand with these steps:
(a)
Turn the cam lock fasteners on each side of the panel, and pull the panel from the P8 control stand.
(b)
Disconnect the connectors DM247 and DS127 behind the module.
S 024-009
(3)
Remove the switch from the panel with these steps:
(a)
Disconnect the set screw and remove the switch knob.
(b)
Remove the lightplate from the panel.
(c)
Disconnect the four screws that hold the switch and the switch plate to the panel, and remove the autobrake selector switch with the switch plate.
(d)
Disconnect the three screws that hold the switch plate to the switch, and remove the switch from the switch plate.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-42-10
ALL ú ú 04 Page 401 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
PILOTS'CONTROL STAND PANEL, P8
SEE A
KNOB
FLIGHT COMPARTMENT
LIGHTPLATE
AUTOBRAKE CONTROL PANEL, M247
SEE B
CONNECTOR
CONTROL STAND
PILOTS' CONTROL STAND PANEL, P8 A
Autobrake Selector Switch Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-42-10
ALL ú ú 01 Page 402 ú Jun 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
AUTOBRAKE CONTROL PANEL, M247
B
Autobrake Selector SwitchFigure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-42-10
ALL ú ú 01 Page 403 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
TASK 32-42-10-414-010
3. Autobrake Selector Switch - Installation________________________________________
A. Consumable Materials
(1)
A00648 Loctite 242 - MIL-S-46163(1)
B.
References
(1)
AMM 29-11-00/201, Main Hydraulic Supply System
(2)
AMM 34-21-00/201, Inertial Reference System
(3)
IPC 32-42-11, Fig. 5
(4)
SSM 32-41-02
(5)
WDM 32-41-32
C.
Access
(1)
Location Zones 222 Control Cabin, RH 118 Elecrical & Electronics Compartment, R.H.
(P180 DC Power Distribution Panel)
D. Procedure
S 424-011
(1)
Install the autobrake selector switch in the panel with these steps:
(a)
Install the autobrake selector switch onto the switch plate with three screws, and tighten the screws.
(b)
Apply sealant to the threads of each screw, used to attach the switch plate to the panel.
(c)
Install the switch plate with the autobrake selector switch to the panel with four screws, and tighten the screws.
(d)
Install the lightplate on the panel.
(e)
Install the knob on the switch post, and tighten the set screw.
S 414-012
(2)
Install the Autobrake Control Panel into the Pilots' Control Stand, P8, with these steps:
(a)
Connect the connectors, DM247 and DS127, behind the module.
(b)
Put the module into its position in the P8 stand, and tighten the fasteners.
S 864-035
(3)
Remove the DO-NOT-CLOSE tag and close this circuit breaker:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(69)
