S 864-015

 (7)  
Release the parking brake.

 S 214-058

 (8)  
Make sure that the PARKING BRAKE ON indication does not show on the EICAS.

 S 864-059

 (9)  
Open this circuit breaker and attach a DO-NOT-CLOSE tag:

 (a)  
P6 Main Power Distribution Panel 1) 6L18 PARK BRAKE

 S 864-064
 (10)
 Remove pressure from hydraulic system 4 (AMM 29-11-00/201).

 S 844-065

 (11)
 Release hydraulic fluid from the brake accumulator:

 (a)  
Look at the HYD BRAKE PRESS gage on the captain's instrument panel.

 (b)  
Push on the brake pedals fully 10 times.

 (c)  
Make sure the pressure does not decrease the last time you operate the brake pedals.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-44-05
 ALL  ú ú 01 Page 403 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 D. Procedure
 S 024-053
 CAUTION: BE CAREFUL TO KEEP CONTAMINATION OUT OF THE PARKING BRAKE
_______ MODULE ASSEMBLY. CONTAMINATION CAN CAUSE A MALFUNCTION OF THE PARKING BRAKE MODULE.
 (1)  
Remove the valve assembly.

 (a)  
Disconnect the DV23 electrical connector from the electric motor on the parking brake module.

 (b)  
Put a cap on the plug and the receptacle.

 (c)  
Remove four cap screws that attach the valve assembly to the module.

 (d)  
Pull the valve assembly for the parking brake from the parking brake module.

 (e)  
Remove the six backup rings and the three O-rings.

 (f)  
Discard the O-rings.

 S 494-066
 (2)  Put a plug on the hole in the parking brake module.
 TASK 32-44-05-424-027
 3. Installation of the Parking Brake Valve Assembly (Fig. 401)
________________________________________________
 A. Consumable Materials
 (1)  
D00288 Lubricant - MCS 352

 B.
References

 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 24-22-00/201, Manual Control

 (3)  
AMM 29-11-00/201, Main Hydrualic Supply System

 (4)  
IPC 32-44-04 Fig. 1

 (5)  
SSM 32-44-01

 (6)  
WDM 32-44-11

 C.
Access

 (1)  
Location Zones
 138 Body Landing Gear Well - Right
 221 Control Cabin, L.H.
 222 Control Cabin, R.H.

 D.
Procedure

 (1)  
Lubricate new O-rings and backup rings.

 S 644-031
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-44-05
 ALL  ú ú 01 Page 404 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 434-032
 (2)  Install the O-rings and backup rings on the valve assembly.
 S 424-054 CAUTION: BE CAREFUL TO KEEP CONTAMINATION OUT OF THE PARKING BRAKE
_______ MODULE ASSEMBLY. CONTAMINATION CAN CAUSE A MALFUNCTION OF THE PARKING BRAKE MODULE.
 (3)  
Install the valve assembly.

 (a)  
Put the valve assembly into the parking brake module.

 CAUTION: DO NOT TURN THE PARKING BRAKE VALVE ASSEMBLY WHEN YOU
_______ PUSH IT INTO THE PARKING BRAKE MODULE. YOU CAN EASILY CAUSE DAMAGE TO THE BACKUP RINGS AND O-RINGS.
 1) Align the valve assembly until the electrical connector points down in a straight direction. 2) Align the holes in the valve assembly with the holes in the parking brake module.
 (b)  
Carefully push the valve assembly into the parking brake module.

 (c)  
Install 4 cap screws and tighten them to 40-60 pound-inches.

 (d)  
Install a lockwire.

 (e)  
Connect the electrical connector DV23 to the electric motor on the parking brake module.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 7(124)