(c)  
Adjust the straps and turn the inlet cowl until it is in the nose up or nose down position.

 CAUTION: IF THE INLET COWL IS PUT IN STORAGE IN THE NOSE UP
_______ POSITION, YOU MUST BE CAREFUL TO PREVENT DAMAGE TO THE TAI DUCT. IF THE TAI DUCT HITS OTHER OBJECTS, DAMAGE TO THE INLET COWL CAN OCCUR.
 (d)  
If the inlet cowl is put in storage in the nose up position, move the TAI duct (1) for the inlet cowl into the hole in the support (or clearance in the sandbags) as the inlet cowl is lowered to the support (Fig. 401).

 (e)  
Lower the inlet cowl on the platform or sandbags, and move the TAI duct if it is necessary.

 S 094-009-N00
 (8)  Remove the sling from the inlet cowl, if the same inlet cowl is not installed (Fig. 403).
 (a)  Remove the tension from the sling.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-01
 ALL  ú ú N01 Page 407 ú Jun 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES /MAINTENANCE MANUAL ////////////////////////

Inlet Cowl Installation
Figure 404

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-01
 ALL  ú ú N01 Page 408 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(b)
Remove the spindles from the inlet cowl.

 (c)
Put the sling away from the inlet cowl.

 (d)
Release the hoist hook from the sling link.

 TASK 71-11-01-404-010-N00
 3. Install the Inlet Cowl
______________________
 A. Special Tools and Equipment
 (1)
A71005-33 Inlet Cowl Sling

 B.
Standard Tools and Equipment

 (1)  
Hoist - Single Cable Ratchet, 1500-pound
 (680-kg) capacity, with the safety
 hooks, L4H150, Ingersall Rand,
 Shippensberg, PA

 (2)  
Dynamometer - 0-1000 pound (0-500 kg) capacity,
 | 2% accuracy, AP30006-0027,

 W. C. Dillon Co. Inc., Van Nuys, CA (not necessary if the crane includes the adjustable load limiter)

 C.
Parts

 ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Cowl - Inlet | 71-00-51 | 01 | 130 | | | 2 | Coupling (Clamp) | 30-21-06 | 01 | 5 | | | 3 | Gasket (Seal) | | | 10 | | 402 | 4 | Cowl - Inlet | 71-00-51 | 01 | 130 | | 404 | 1 | Cowl - Inlet | 71-00-51 | 01 | 130 | | | 2 | Spacer | 71-11-01 | 01 | 65 | | | 3 | Washer | | | 60 | | | 4 | Bolt | | | 55 | | | 5 | Shear Pin | | | 40 | | | 6 | Nut | | | 50 | | | 7 | Washer | | | 45 | 2.....….........…...................................…..........…......…........1
 D. References
 (1)
AMM 71-11-04/201, Fan Cowl Panels

 (2)
AMM 71-11-04/401, Fan Cowl Panels

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 71-11-01
 ALL  ú ú N01 Page 409 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(3)  
AMM 73-21-03/401, EEC Inlet Total Pressure/Temperature
 (PT2/TT2) Probe

 E.  
Access

 (1)  
Location Zone
 411 Engine 1 - Inlet Cowl
 421 Engine 2 - Inlet Cowl
 431 Engine 3 - Inlet Cowl
 441 Engine 4 - Inlet Cowl

 F.  
Procedure

 S 434-011-N00
 (1)  Install the shear pins (5), washers (7), and nuts (6) to the engine flange A if they are not there.
 (a)  Tighten the nuts (6) to 50-75 pound-inches (5.6-8.5 newton-meters).
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 動力裝置 POWER PLANT 2(63)