曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

PLAN WILL NOT AUTO-SEQUENCE TO THE NEXT
LEG. THE AIRCRAFT WILL CONTINUE TO FLY
OVER THE TO WAYPOINT ON LAST DESIRED
TRACK (0° ROLL STEERING) WITH NAV AND
VNAV FLAGS OUT OF VIEW ON THE HSI. IT IS
THE RESPONSIBILITY OF THE PILOT TO TAKE
APPROPRIATE ACTION TO CONTINUE
ACCURATE NAVIGATION OF THE AIRCRAFT. HE
MAY GO “DIRECT TO” OR EDIT THE GAP OUT OF
THE FLIGHT PLAN.
Designate Route Waypoint as Fly-Over Waypoint
A flyover waypoint is a waypoint that will cause the navigation
computer to delay making an automatic leg change until the aircraft
is over the waypoint. Flyover waypoints defined in a route have no
effect until the route is copied into the flight plan. A flyover waypoint
is indicated by an asterisk (*) following the waypoint identifier on the
ROUTE display page. With the first ROUTE page in view, the
following procedure may be used to designate (or cancel) a
waypoint as a flyover waypoint:
1. Use the NEXT and PREV function keys to display the desired
waypoint.
2. Use the line select keys to position the cursor over the waypoint
to be defined as a flyover waypoint.
3. Press the OVFLY line select key. An asterisk (*) will appear
after the waypoint identifier indicating that it is a flyover
waypoint.
The waypoint flyover designation is removed in the same manner as
it was created; i.e., pressing the CNCL OVFLY key with the cursor
over the flyover waypoint identifier.
Section IV
Data Base
2423sv602 4-29
Change 1
Add Waypoint(s) To Route
With the first ROUTE page displayed, add a waypoint to the route as
follows:
1. Use the NEXT and PREV function keys to display the desired
portion of the ROUTE.
2. Use the line select key to position the cursor over the waypoint
that will follow the new waypoint.
3. Enter the new waypoint using the LIST function or by typing in
the identifier. When the new waypoint is entered, it will be
inserted in the position selected and the waypoint under the
cursor will have advanced to the next position.
Edit Route Name
With the ROUTE page displayed, edit the Route Name as follows:
1. Press ENTER key to place cursor over the Route Name field.
2. Type in the new route name and press ENTER.
Delete Waypoint(s) From Route
With the first ROUTE page displayed, delete waypoint(s) from route
as follows:
1. Use the NEXT and PREV keys to display the desired waypoint.
2. Use the line select key to position the cursor over the waypoint
to be deleted.
3. Press DEL line select key.
NOTE: If it is desired to delete the remainder of the route, enter a
reference number greater than the reference number of
the last waypoint on the route (for example, 98). Do not
enter 99, or the entire flight plan will be deleted.
Section IV
Data Base
4-30 2423sv602
Change 1
Change Waypoint In Route
A waypoint in a route is changed by adding the new waypoint ahead
of the old waypoint (waypoint to be changed) and then deleting the
old waypoint. With the first ROUTE page displayed, change a
waypoint in a route as follows:
1. Use the NEXT and PREV function keys to locate the desired
waypoint.
2. Position the cursor over the first waypoint to be changed.
3. Enter the new waypoint using the LIST function or by typing the
identifier. When the new waypoint is entered, it will be inserted
at the position selected and the waypoint under the cursor will
advance to the next position.
4. Enter the reference number associated with the waypoint that
will follow the added waypoint. The changed waypoints will be
removed from the route.
Section IV
Data Base
2423sv602 4-31
Change 1
PILOT DEFINED SIDS
The PLT/SID page is designed to allow the creation or deletion of
SID data base records. To edit the SID records, an airport must be
defined. A new SID can be defined by either renaming an existing
one or creating one by defining a new runway, an enroute transition
or by editing (adding or deleting) legs in a common procedure.
Existing SIDs can be deleted (along with all associated transitions)
by entering the SID name and then requesting deletion. Individual
transitions can be deleted by selecting the transition and the
associated SID and then requesting deletion.
This page is also used to gain access to a specific SID procedure
that needs to be edited. When the SID is defined, pages will be
appended to this page that include the SID procedure legs (PLT/SID
2/3 and 3/3). To access the PLT/SID page press SID prompt on the
DATA/PLT menu page.
The page consists of required and optional fields. When the page is
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：龐巴迪挑戰(zhàn)者手冊10(46)