曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

this line.
Noo,, pprreessss eeiitthheerr CLLR kkeeyy..
ELECTRICAL MENU Abnormal operation (C) 15/54
On the E/WD, you can read that the autopilot
has disengaged. Let’s deal with this, first.
To continue the procedure, you have to clear
this line.
Noo,, pprreessss eeiitthheerr CLLR kkeeyy..
ELECTRICAL MENU
Abnormal operation (C) 16/54
Read the title of the failure.
The red EMER CONFIG title means that you
are in an ELECTRICAL EMERGENCY
CONFIGURATION.
ELECTRICAL MENU
Abnormal operation (C) 17/54
The red message LAND ASAP recommends to
land as soon as possible.
ELECTRICAL MENU
Abnormal operation (C) 18/54
Observe that, you have to maintain a minimum
speed when the RAT is extended.
CAUTION
Below this minimum speed, the RAT will stall
leading to the aircraft being supplied by batteries
only.
The PF will ask you to perform the ECAM
actions.
ELECTRICAL MENU
Abnormal operation (C) 19/54
You will try to reset the generators.
Here, this will be done for you.
ELECTRICAL MENU
Abnormal operation (C) 20/54
The reset of the generators has not been
successful.
Before continuing with the procedure, let’s
look at how to access an ECAM page when the
lower ECAM is not available.
ELECTRICAL MENU
Abnormal operation (C) 21/54
An ECAM page can be called up on the upper
ECAM by pressing and holding its associated pb
sw on the ECAM control panel.
Caallll tthhee ECAMELLEC ppaaggee..
ELECTRICAL MENU Abnormal operation (C) 22/54
Noo,, pprreessss tthhee ELLEC kkeeyy..
An ECAM page can be called up on the upper
ECAM by pressing and holding its associated pb
sw on the ECAM control panel.
ELECTRICAL MENU Abnormal operation (C) 23/54
Noo,, pprreessss tthhee ELLEC kkeeyy..
An ECAM page can be called up on the upper
ECAM by pressing and holding its associated pb
sw on the ECAM control panel.
ELECTRICAL MENU Abnormal operation (C) 24/54
The page is displayed on the upper ECAM as
long as the associated key is maintained pressed.
On the ECAM ELEC page, note that the EMER
GEN supplies the AC ESS bus and, via the ESS
TR, the DC ESS bus.
ELECTRICAL MENU
Abnormal operation (C) 25/54
As soon as the ECP pb sw is released, the
E/WD is displayed on the upper display.
ELECTRICAL MENU
Abnormal operation (C) 26/54
As the previous reset of the generators was
not successful, we will carry on with the
procedure.
Coonnttiinnuuee ECAMaaccttiioonn..
ELECTRICAL MENU Abnormal operation (C) 27/54
As the previous reset of the generators was
not successful, we will carry on with the
procedure.
Noo,, pprreessss tthhee BUS TTIIE ppbb ssw..
ELECTRICAL MENU Abnormal operation (C) 28/54
As the previous reset of the generators was
not successful, we will carry on with the
procedure.
Noo,, pprreessss tthhee BUS TTIIE ppbb ssw..
ELECTRICAL MENU
Abnormal operation (C) 29/54
The BUS TIE pb sw in the OFF position
segregates the two sides of the system.
By doing this, a short circuit can be isolated
and might give you the possibility to reset one
generator.
The procedure asks you to try to reset the
generators again. Here, this will be done for you.
ELECTRICAL MENU
Abnormal operation (C) 30/54
Again, the reset of the generators has not been
successful.
As the next steps concern other systems, we
will stop here and study the indications on the
right side of the E/WD.
ELECTRICAL MENU
Abnormal operation (C) 31/54
Notice the amber NAV, F/CTL and AUTO FLT
system titles.
This means that these systems are affected by
the failure. Their related procedures are stacked
after the current one and will appear with the
completion of the EMER CONFIG procedure.
ELECTRICAL MENU
Abnormal operation (C) 32/54
Notice also the visible secondary failures
concerning the CAB PRESS, HYD and FUEL
systems. There may be other secondary failures
that are not yet displayed since there is an
overflow indication(green arrow).
We will now jump to the end of the EMER
ELEC procedure and see how you can view the
secondary failures.
ELECTRICAL MENU
Abnormal operation (C) 33/54
The system titles have disappeared when their procedures are
completed.
The complete list of the secondary failures is now visible. As the
lower ECAM is not available, you will have to manually call the
ECAM pages associated with the secondary failures on the E/WD.
You have to press and hold the related key on the ECP in the
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：空客a320飛機概述1(25)