曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R 
R  (5) Put the clamp (10) on the servo control (5). 
R  (6) Put the servo control (5) in position at the bracket (52) and (65). 
R  (7) Make sure that the items that follow are correctly installed in the 
R  brackets (52) and (65): 
R  - The locking plates (53) and (64) 
R  - The bushes (34), (36), (73) and (74). 
R
 (8) Connect the servo control (5) to the bracket (52) of the vertical
 stabilizer (1) as follows:
 (Ref. Fig. 405/TASK 27-24-51-991-007) 
R  NOTE : In this procedure it is necessary for two persons to install____ 
R  the items that follow in the brackets (52): 
R  - The servo control (5) 
R  - The sealing rings (35). 
R  (a) Apply a thin layer of the COMMON GREASE (Material No. 04-004) to 
R  the sealing rings (35). 
R  (b) Attach the sealing rings (35) in position at the eye-end bearing 
R  of the servo control (5). 
R  (c) Use the two GAGE - FEELER 0.25 mm (0.0098 in.) thick to carefully 
R  move the servo control (5) into the bracket (52).

 

R R R  (d) Align the eye-end bearing of the servo control (5) and the sealing rings (35). Do this with the bolt hole in the bracket (52). 
R  (e) Install the bolt (55) through the connection of the bracket (52) and the servo control. 
R  (f) Connect the servo control (5) with the STA-LOK nuts (Ref. TASK 20-22-00-400-001):
 1_ Install the cupwasher (51) and the slotted nut (50) on the bolt (55).
 2_ Use the WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-374-7500) and TORQUE the slotted nut (50) to between 7.0 and 8.0 m.daN (51.62 and 58.99 lbf.ft).
 3_ If the spring ring (48) was removed, install it on the tab washer (49). 
R R R  4_  Use the TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454(SL90-313-7500) and install the tab washer (49) with the spring ring (48). Do this on the slotted nut (50).
 5_ Install the bolt (56) through the bolt (55).
 6_ Install the washer (47) and the nut (46) on the bolt (56).
 7_ TORQUE the nut (46) to 1.0 m.daN (88.49 lbf.in) and then loosen it to the next cotter pin hole.
 8_ Safety the nut (46) with a new cotter pin (45).
 (9) Connect the servo control (5) to the bracket (65) of the rudder (2) as follows: (Ref. Fig. 406/TASK 27-24-51-991-008) 
R R R R  NOTE : In this procedure it is necessary for two persons to install____ the items that follow in the bracket (65): - The servo control (5) - The sealing rings (74). 
R R  (a) Apply a thin layer of the COMMON GREASE (Material No. 04-004) to the sealing rings (74). 
R R  (b) Attach the sealing rings (74) in position at the eye-end bearing of the servo control (5).

 

R R  (c) Use the two GAGE - FEELER 0.25 mm (0.0098 in.) thick to carefully move the servo control (5) into the bracket (65). 
R R R  (d) Align the eye-end bearing of the servo control (5) and the sealing rings (74). Do this with the bolt hole in the bracket (65). 
R  (e) Install the bolt (62) through the connection of the bracket (65) and the servo control (5). 
R  (f) Connect the servo control (5) with the STA-LOK nuts (Ref. TASK 20-22-00-400-001):
 1_ Install the cupwasher (66) and the slotted nut (67) on the bolt (62). 
R  2_ Use the WRENCHES - NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-374-7500) and TORQUE the slotted nut (67) to between 7.0 and 8.0 m.daN (51.62 and 58.99 lbf.ft).
 3_ If the spring ring (69) was removed, install it on the tab washer (68). 
R R R  4_  Use the TOOL - INSTALLATION, TAB WASHERS STA-LOK NSA5454(SL90-313-7500) and install the tab washer (68) with the spring ring (69). Do this on the slotted nut (67).
 5_ Install the bolt (61) through the bolt (62).
 6_ Install the washer (70) and the nut (71) on the bolt (61).
 7_ TORQUE the nut (71) to 1.0 m.daN (88.49 lbf.in) and then loosen it to the next cotter pin hole.
 8_  Safety the nut (71) with a new cotter pin (72).
R R R R R  (10) Apply a thin layer of the SPECIAL MATERIALS (Material No. 05-005) (Ref. TASK 51-75-13-916-002) to all attachment parts made of steel which you can see. Do not apply the SPECIAL MATERIALS (Material No. 05-005) to the spherical bearings of the servo control (5). 

R 1EFF : 001-003, 051-054, 1 27-24-51Page 441 1 1 Aug 01/05 1 1 1CES 1

 (11) Connect the spring rod (21) to the input lever (17) of the servo control (5) as follows: (Ref. Fig. 405/TASK 27-24-51-991-007) 
R R R R R (a) Make sure that the items that follow are clean and are correctly installed in the input lever (17): - The flanged bushes (19) and (24) - The sliding bush (20). 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱2(143)