曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  (a) Put the hydraulic bracket (45) in the installation position. 
R  (b) Install the bolts (42) with the washers (43) and the nuts (44). 
R  (13) Connect the control rod (27) to the bellcrank (31): 
R  (a) Cut, remove and discard the lockwire which temporarily safetied 
R  the bush (26) in the bellcrank (31). 
R  (b) Put the eye-end of the control rod (27) in position at the 
R  bellcrank (31). 
R  (c) Install the bolt (25) with the washer (30) and the nut (29). 
R  (d) TORQUE the nut (29) to 0.8 m.daN (70.79 lbf.in) and then loosen 
R  it, if necessary, to the next cotter pin hole. 
R  (e) Safety the nut (29) with a new cotter pin (28). 
R  (14) Install the control rod on the rudder mechanical control (Ref. TASK 
R  27-21-00-840-001).
 Subtask 27-22-51-865-051 
R  F. Remove the safety clip(s) and the tag(s) and close this(these) circuit
 breaker(s):
 5CC1, 5CC2, 14CC1, 14CC2, 15CC

 

 Subtask 27-22-51-860-053
 G. Preparation for the Test NOTE : Do the worksteps that follow, if you install a rudder trim
____
 actuator with the part number 6137-3. If you install a rudder trim R actuator with the part number 6137-4 or 6137-5, refer to the R subsequent subtask.
 (1)
 Remove the PIN - RIGGING (98D27207548000) (18) from the bellcrank of the rudder control unit.

 (2)
 Remove the PIN - RIGGING (98D27207547000) (17) from the rudder cable quadrant.

 (3)
 Remove the PIN - LOCKING (6137-013) (19) from the rudder trim actuator (3).

 (4)
 Remove the blanking plug (16) from the storage hole of the rudder trim actuator (3).

 (5)
 Make sure that the O-ring on the blanking plug (16) is installed and in good condition.

 (6)
 Install the blanking plug (16) in the rigging hole of the rudder trim actuator (3).

 (7)
 TORQUE the blanking plug (16) to to 0.10 m.daN (8.84 lbf.in).

 (8)
 Safety the blanking plug (16) with the lockwire MISCELLANEOUS (Material No. 19-010).

 (9)
 On the overhead panel 23VU, push the FLT CTL/FAC 1 pushbutton switch. The OFF legend goes off.

 (10) On the overhead panel 24VU, push the FLT CTL/FAC 2 pushbutton switch. The OFF legend goes off.
 Subtask 27-22-51-860-057
 H. Preparation for the Test NOTE : Do the worksteps that follows, if you install a rudder trim
____ R actuator with the part number 6137-4 or 6137-5.
 (1)
 Remove the PIN - RIGGING (98D27207548000) (18) from the bellcrank of the rudder control unit.

 (2)
 Remove the PIN - RIGGING (98D27207547000) (17) from the rudder cable quadrant.

 (3)
 Remove the PIN - LOCKING (6137-060) (19) from the rudder trim actuator (3).

 (4)
 Make sure that the O-ring on the plug is installed and in good condition.

 (5)
 Install the plug in the rigging hole of the rudder trim actuator (3).

 (6)
 Safety the plug (16) with the lockwire, MISCELLANEOUS (Material No. 19-010).

 (7)
 Remove the PIN - RIGGING (98D27207546000) (20) from the bellcrank of the servo actuator 1025GM.

 (8)
 On the overhead panel 23VU, push the FLT CTL/FAC 1 pushbutton switch. The OFF legend goes off.

 (9)
 On the overhead panel 24VU, push the FLT CTL/FAC 2 pushbutton switch. The OFF legend goes off.

 

 Subtask 27-22-51-720-050
 J. Test
 NOTE : Do the worksteps that follow, if you install a rudder trim
____ actuator with the part number 6137-3. If you install a rudder trim actuator with the part number 6137-4 or 6137-5, refer to the subsequent subtask.
 (1)
 Do the operational test of the rudder trim actuation (Ref. TASK 27-22-00-710-002).

 (2)
 Make sure that the PIN - LOCKING (6137-013) (19) is removed before you do the operational test of the rudder trim actuation.

 (3)
 If you operate the aircraft in actual CAT 3 conditions, do these tests:

 -AFS-Test (Ref. TASK 22-96-00-710-001) and Land Test (Ref. TASK 22-97-00-710-001).
 1EFF : ALL 1 27-22-51Page 431 1 1 Nov 01/04R 1 1 1CES 1

 Subtask 27-22-51-720-052
 K. Test NOTE : Do the worksteps that follow, if you install a rudder trim
____
 actuator with the part number 6137-4 or 6137-5.

 (1)
 Do the operational test of the rudder trim actuation (Ref. TASK 27-22-00-710-002).

 (2)
 Make sure that the PIN - LOCKING (6137-060) (19) is removed before you do the operational test of the rudder trim actuation.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱2(89)