REFERENCE DESIGNATION
-------------------------------------------------------------------------------
**ON A/C 301-399,
27-21-44-991-002-A Fig. 402A
**ON A/C ALL
27-21-44-991-003 Fig. 403
3. Job Set-up
__________
Subtask 27-21-44-010-052
A. Get Access
(1)
Make sure that the access platform is in position.
(2)
Make sure that the access door 811 is open.
(3)
Make sure that the warning notice to tell persons not to operate the Green and the Yellow hydraulic systems is in position.
(4)
Make sure that the warning notice to tell persons not to operate the pedals is in position.
(5)
Make sure that the PIN, RIGGING - RUDDER CONTROL (98A27901002000)
(36) is in position on the tension regulator.
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 401/TASK 27-21-44-991-001)
**ON A/C 301-399,
(Ref. Fig. 401A/TASK 27-21-44-991-001-A)R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 402/TASK 27-21-44-991-002)
**ON A/C 301-399,
(Ref. Fig. 402A/TASK 27-21-44-991-002-A)
**ON A/C ALL
(Ref. Fig. 403/TASK 27-21-44-991-003) R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-21-44-420-050
A. Installation of the CAPT Yaw/Brake Bellcrank
(1)
Apply COMMON GREASE (Material No. 04-004) to the attachment hardware.
(2)
Turn the yaw bellcrank (2) 90 deg. and install the yaw/brake bellcrank on the beam (40).
(3)
Install the sleeves (45) and (73).
(4)
Install the bolts (50), (49); install and tighten the new nuts (41).
(5)
Install the rod (42) on the sleeve (45) and install the bolt (43).
(6)
Install the washer (46) and install and tighten the nut (47). Safety it with the new cotter pin (48).
(7)
Install the rod (62) and install the bolt (51).
(8)
Install the washer (53), install and tighten the nut (54). Safety it with the new cotter pin (55).
(9)
Install the rod (66), install the bolt (70).
(10)
Install the washer (61) and install and tighten the nut (59). Safety it with the new cotter pin (60).
(11)
Install the rod (69), install the bolt (52).
(12)
Install the washer (56) and install and tighten the nut (57). Safety
it with the new cotter pin (58).
(13)
Install the rod (68), install the bolt (67).
(14)
Install the washer (65) and install and tighten the nut (64). Safety it with the new cotter pin (63).
(15)
Install the PIN, RIGGING - RUDDER CONTROL (98A27901002000) (35) on the yaw/brake bellcranks of the CAPT and F/O.
(16)
Push and hold the pin on the transducer unit 25CE1 to lock the input lever in the zero position.
NOTE : The pin is a part of the transducer unit 25CE1.
____
(17)
Install the rods (33) and (29) and install the bolt (34). If necessary, adjust the length of the rod (29) as follows:
(a)
Cut and discard the lockwire.
(b)
Loosen the nuts (25) and (28) and disengage the lockwashers (26) and (27).
(c)
Adjust the length of the rod (29) until you can install the bolt (34).
(d)
Engage the lockwashers (26) and (27) and tighten the nuts (25) and (28). Safety them with Lockwire corrosion resistant steel dia
0.8 mm (0.03 in.).
(18)
Disengage the pin to release the input lever of the transducer unit 25CE1.
(19)
Install the washer (30), install and tighten the nut (31). Safety it with the new cotter pin (32).
(20)
Install the rod (9) and the bolt (1).
(21)
Install the washer (18), install and tighten the nut (20). Safety it with the new cotter pin (19).
(22)
Install the rod (4) and install the bolt (3). If necessary, adjust the length of the rod (4) as follows:
(a) Cut and discard the lockwire.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-21-44Page 414 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(b) Loosen the nuts (5) and (8) and disengage the lockwashers (6) and (7).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM FLIGHT CONTROLS 飛行操縱2(27)
