B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
Power Supply 29-10-00-864-003 Depressurize the Blue Hydraulic System 29-22-00-869-005 Extension of the Ram Air Turbine (RAT) on the Ground 29-22-00-869-006 Retraction of the Ram Air Turbine (RAT) on the Ground 31-60-00-860-001 EIS Start Procedure 31-60-00-860-002 EIS Stop Procedure 29-30-00-991-003-A Fig. 402A
3. Job Set-up
__________
Subtask 29-30-00-860-053
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Do the EIS start procedure (Upper ECAM DU, lower ECAM DU only) (Ref. TASK 31-60-00-860-001).
(3)
Make sure that the ECAM upper DU shows the RAT FAULT warning.
4. Procedure
_________
(Ref. Fig. 402A/TASK 29-30-00-991-003-A)
Subtask 29-30-00-040-051
A. Deactivation of the RAT FAULT Warning
(1) Do a visual check of the left belly fairing to make sure that the RAT is not extended.
NOTE : If the RAT is extended, you must do the trouble shooting
____ procedure of the system before you can dispatch the aircraft.
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 29-30-00Page 413 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Location of RAT - Components
Figure 402A/TASK 29-30-00-991-003-A
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 29-30-00Page 414 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1 NOTE : If the RAT is not extended, continue with the subsequent
____
procedure.
(2)
Open the access panels 195BB and 197EB.
(3)
Do the test of the lights on the RAT control panel 3GE.
(a)
Open the cover of the RAT control panel 3GE.
(b)
Set the 28V DC switch to ON.
(c)
Set and hold the LAMP TEST switch and make sure that the red warning light ACTUATOR PRESSURE and the green indicator light RAT STOWED come on.
NOTE : If the red warning light ACTUATOR PRESSURE or the green
____ indicator light RAT STOWED does not come on, replace the applicable bulb.
(d)
Release the LAMP TEST switch.
(e)
Set the 28V DC switch to OFF.
(4)
Pressurize the Blue hydraulic system (Ref. TASK 29-10-00-863-003).
(5)
Look to see that the red warning light ACTUATOR PRESSURE is on. NOTE : If the red warning light ACTUATOR PRESSURE is off, continue
____
with the work step (7).
(6)
If the red warning light ACTUATOR PRESSURE is on:
(a)
Disconnect the electrical connector 1GE-E from the RAT actuator.
(b)
Look at the ECAM upper DU and see if the RAT FAULT warning shows.
(c)
If the RAT FAULT warning shows on the ECAM upper DU, there is a fault of the wiring:
1 Connect the electrical connector 1GE-E.
_
2 Continue with the work step (7) (a).
_
(d) If the RAT FAULT warning does not show on the ECAM upper DU: 1 Depressurize the Blue hydraulic system (Ref. TASK 29-10-00-
_
864-003).
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 29-30-00Page 415 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1 2 Wait a short time to make sure that the hydraulic pressure is
_
released.
3 Connect the electrical connector 1GE-E.
_ 4 Look at the ECAM upper DU to see if the RAT FAULT warning
_
shows.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM HYDRAULIC POWER 液壓6(113)
