20-25-52 Page 13
Wire Protection Tool - Hydraulic/Pneumatic Crimping Tool ICORE 16-0803 R Figure 007
20-25-52 Page 14
______________________________________________________7. Crimping Pliers ICORE 19600 and REMA 5800-00 type HP50
A. Designation
R (Ref. Fig. 008) Crimping pliers ICORE 19600 and REMA 5800-00 are used in replacement of ICORE 16-803 for crimping sleeves on backshells, end pieces and conduit fittings.
B. Die table
(1) For ICORE 19600: ---------------------------------------------------| CONDUIT SIZE | DIE ICORE P/N | |---------------------------|---------------------| | VW-06 | V-06 | 16-1234-06 | |-------------|-------------|---------------------| | VW-09 | V-09 | 16-1234-09 | |-------------|-------------|---------------------| | VW-10 | V-10 | 16-1234-10 | |-------------|-------------|---------------------| | VW-12 | V-12 | 16-1234-12 | |-------------|-------------|---------------------| | VW-14 | V-14 | 16-1234-14 | |-------------|-------------|---------------------| | VW-16 | V-16 | 16-1234-16 | |-------------|-------------|---------------------| | VW-20 | V-20 | 16-1234-20 | |-------------|-------------|---------------------| | VW-24 | V-24 | 16-1234-24 | ---------------------------------------------------
20-25-52 Page 15
Wire Protection Tool - Crimping Pliers ICORE 19600 and REMA 5800-00 type HP50 R Figure 008
20-25-52 Page 16
(2) For REMA 5800-00 type HP50: -------------------------------------------------| CONDUIT SIZE | DIE REMA P/N | |---------------------------|-------------------| | VW-06 | V-06 | VW-06 | |-------------|-------------|-------------------| | VW-09 | V-09 | VW-09 | |-------------|-------------|-------------------| | VW-10 | V-10 | VW-10 | |-------------|-------------|-------------------| | VW-12 | V-12 | VW-12 | |-------------|-------------|-------------------| | VW-14 | V-14 | VW-14 | |-------------|-------------|-------------------| | VW-16 | V-16 | VW-16 | -------------------------------------------------
20-25-52 Page 17
Oct 01/04
R
_______________________________________________________________________
PUSHBUTTON SWITCH AND INDICATOR LIGHT TOOLS - DESCRIPTION AND OPERATION
_______1. General
This chapter deals with description of pushbutton switches and indicator
light tools.
_____2. Tools
(Ref. Fig. 001, 002)
OUT74 or 851-30486-510 Extractor - Head
(ex MSC 584-901)
or 58T-101
OUT75 or 851-30486-506 Guiding Tool
(ex MSC 584-501)
or 58T-108
R or
R OUT217 or 29085-001 Guiding Tool (only for ABS0951)
OUT141 or 851-30486-507 Extractor - Connector
(ex MSC 584-502)
or 58T-107
OUT87-1 or MSC 584-508 Screwdriver - Dynamometric
R (ex MSC 584-510) 0.12 to 0.14 N.m
or 58T-106
or TLS022 + Blade
AMP DP27478 SP 0.3 x 3
R OUT87-2 Screwdriver - Dynamometric (only for ABS0951)
R 0.085 to 0.10 N.m
No Specific Screwdriver - Blade Width 3 mm
(0.118-in.) max.
OUT70 Fixture
OUT83 or NSA933684 Extractor - Head
_________3. Procedure
R
The procedure is given in the chapter dealing with the pushbutton switches.
20-25-53 Page 1
R Pushbutton Switch and Indicator Light Tools - Description ECE, EATON and POWELL Figure 001
20-25-53 Page 2
R Pushbutton Switch and Indicator Light Tools - Description ECE (Only for NSA) Figure 002
20-25-53 Page 3
_________________________________________________________
TOOLS FOR CIRCULAR CONNECTORS - DESCRIPTION AND OPERATION
R
R
R
_______1. General
This chapter deals with the description and operation of the tools used for
some specific procedures to be applied on connectors.
These tools have the codes that follow:
-UTICA 529, SOURIAU 8498-03 and FACOM 410S - Rubber-jaw pliers
-SOURIAU 8500-30 - Tightening support
___________________________________________________________
2. Rubber-jaw pliers UTICA 529, SOURIAU 8498-03 and FACOM 410S (Ref. Fig. 001)
A. General Rubber-jaw pliers are used to facilitate the installation and removal of backshells and connectors to obtain the correct tightening without damaging the backshells or connectors.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 2(12)
