曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 | | A = with drain hole
 | --------- Size code
 ----------------- Standard P/N
 E0469 A 09
 E0560 A 09
 | | |
 | | ------ Diameter type code 
R  | --------- Metal type code : A = nickel plated copper
 ------------- Standard P/N
 NSA935805 T 12
 NSA935806 T 12
 | | | |
 | | | ------ Type code : no code = no specification
 | | | A = ABS0746 specification
 | | |
 | | ---------- Diameter type code
 | ------------- Conduit type code : T = with braid
 | - = without braid
 --------------------- Standard P/N 
R 
R  ABS0887 B 06 
R  | | | 
R  | | ---- Diameter type code 
R  | -------- Type code : A = Peek conduit (lightweight) 
R  | B = Peek conduit + braid 
R  | C = Peek conduit + braid + halar (E-CTFE) sheath 
R  -------------- Standard P/N
 B. P/N characteristics
 (Ref. Fig. 002)
R  ____NOTE : For NSA935805 and NSA935806 characteristics, refer to chapter 
R  20-33-31 - convoluted conduits.

 

20-33-32 Page 4

R Screened Convoluted Conduit - P/N Characteristics and Description
R ABS0330/0492/0510/0511/0631/887B and C, E0469, E0560 and NSA935805T/806T Figure 002

20-33-32 Page 520-33-32 Page 620-33-32 Page 7

 (1) Temperature 
R  - For ABS0492, ABS0510, ABS0511, ABS0887, E0469, E0560, NSA935805T 
R  and NSA935806T:
 Minimum operating temperature is -55 deg.C (-67.00 deg.F)
 - For ABS0330, ABS0631:
 Minimum operating temperature is -70 deg.C (-94.00 deg.F) 
R  - For ABS0492, ABS0510, ABS0511 and ABS0887C:
 Maximum operating temperature is 165 deg.C (329.00 deg.F) 
R  - For ABS0330, ABS0631, ABS0887B, E0469, E0560, NSA935805T and 
R  NSA935806T:
 Maximum operating temperature is 260 deg.C (500.00 deg.F) 
R  (2) Diameter type code (only for ABS0887, E0469 and E0560) 
R  ----------------------------------------------------
R  | DIAMETER TYPE CODE | DIAMETER INTERIOR mm (in.)| 
R  |---------------------|----------------------------| 
R  | 04 * | 3 (0.118) | 
R  |--------------------------------------------------| 
R  | 06 | 4,6 (0.181) | 
R  |--------------------------------------------------| 
R  | 09 | 7 (0.275) | 
R  |--------------------------------------------------| 
R  | 10 | 7,6 (0.299) | 
R  |--------------------------------------------------| 
R  | 12 | 8,2 (0.322) | 
R  |--------------------------------------------------| 
R  | 14 | 10,8 (0.425) | 
R  |--------------------------------------------------| 
R  | 16 | 12,3 ( 0.484) | 
R  |--------------------------------------------------| 
R  | 20 | 15,6 (0.614) | 
R  |--------------------------------------------------| 
R  | 24 | 19 (0.748) | 
R  |--------------------------------------------------| 
R  | 28 | 21,8 (0.858) | 
R  |--------------------------------------------------| 
R  | 32 | 24,5 (0.964) | 
R  |--------------------------------------------------| 
R  | 40 ** | 31,4 (1.236) | 
R  ----------------------------------------------------
R  * For E0469 and E0560 only 
R  ** For ABS0887 only 
R

 

 C. Procedures
 (1) Drain holes
 (Ref. Fig. 003)
R  ____NOTE : You can only make drain holes before installation of the 
R  conduit on the bundle and before installation of the end 
R  assembly.
 - Only for conduit with halar sheath (step 1): 
R  Use a soldering iron to cut a 20 mm (0.7874 in.) long window in the 
R  E-CTFE braid. 
R  The window width must not exceed 30% of the protective conduit 
R  circumference. 
R  - Insert a plastic rod in the conduit until it is behind the hole 
R  position. 
R  In the necessary hole position, use a blunt needle to slide the 
R  braid aside with circular movements (step 2). 
R  - Make sure that you strike a "crest" of the convoluted hose below. 
R  - Punch a hole in the convoluted hose with punch pliers or equivalent 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 2(58)