曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  delivery with adhesive sealant. 
R  (a) When used with addition of adhesive sealant: 
R  - Roughen the external side of the shrunken sleeve in the bonding 
R  area and the inner side of the moulding with emery cloth (grain 
R  280 or finer). 
R  - Clean the roughened areas with a cleaning agent. 
R  - In a clean cup, put two equal parts of adhesive sealant 
R  components RAYCHEM S1125 (Material No. 09-531) or equivalent. 
R  - Mix the sealant carefully and apply with a spatula on the 
R  shrunken sleeve and the rear connector bonding areas. 
R  - Install the moulding on the shrunken sleeve and the rear 
R  connector.
 - Select the applicable shrinking tool.
 - Install the applicable reflector on the shrinking tool
 according to the dimensions of the part to be shrunk. 
R  - Start shrinking at the connector (You must start shrinking at 
R  the point where a specified position is required).
R  ____NOTE : During shrinking, turn the moulding in the heat flow, if 
R  possible, to obtain equal distribution of temperature. 
R  - Do not let the harness touch the reflector during shrinking.
 - Shrinking is completed when the mouldings fit closely and when
 the form is flush. 
R  - If used, remove any unwanted sealant immediately with a clean 
R  cloth.

 

R Shrinkable Mouldings - Installation Procedure
R E0096, ABS0266, ABS0312, E0056, DAN218, DAN299, DAN301 and DAN302 Figure 002

20-33-34 Page 520-33-34 Page 6

R  ____NOTE : 90. shrinkable mouldings contain a memory and should be at 
R  a 90. angle after shrinking. It can be necessary during 
R  the shrinking operation to hold the outlet of the moulding 
R  in its 90. position until it is cool. 
R  (b) When delivery-coated with adhesive sealant 
R  - Roughen the external side of the shrunken sleeve in the bonding 
R  area with emery cloth (grain 320 or finer). 
R  - Clean the roughened areas with a cleaning agent. 
R  - Install the moulding on the shrunken sleeve and the rear 
R  connector. 
R  - Select the applicable shrinking tool. 
R  - Install the applicable reflector on the shrinking tool 
R  according to the dimensions of the part to be shrunk. 
R  - Start shrinking at the connector (You must start shrinking at 
R  the point where a specified position is required).
R  ____NOTE : During shrinking, turn the moulding in the heat flow, if 
R  possible, to obtain equal distribution of temperature. 
R  - Do not let the harness touch the reflector during shrinking. 
R  - Shrinking is completed when the mouldings fit closely and when 
R  the form is flush. 
R  - If used, remove any unwanted sealant immediately with a clean 
R  cloth.
R  ____NOTE : 90. shrinkable mouldings contain a memory and should be at 
R  a 90. angle after shrinking. It can be necessary during 
R  the shrinking operation to hold the outlet of the moulding 
R  in its 90. position until it is cool. 
R  (2) Moulding boot (ABS0312, E0056, DAN301 and DAN302) 
R  - Select the applicable shrinkable mouldings and the correct size. 
R  - Install the moulding on the harness. 
R  - Select the applicable shrinking tool. 
R  - Install the applicable reflector on the shrinking tool according to 
R  the dimensions of the part to be shrunk. 
R  - Start shrinking at the point where a specified position is 
R  required). 
R  - Do not let the harness touch the reflector during shrinking. 
R  - Shrinking is completed when the mouldings fit closely and when the 
R  form is flush.
R  ____NOTE : During shrinking, turn the moulding in the heat flow, if 
R  possible, to obtain equal distribution of temperature.

 

 ______________________________________
ATTACHMENT - DESCRIPTION AND OPERATION
 _______

1. General The chapters that follow give the general description and requirements related to the elements which attach, route and install the wiring without
R damage to the aircraft. These elements are separated into several families.
 _________________________2. Structure of the Chapters
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 2(66)