曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (13) Crimp the assembly.
 (14) Cut the braid wires that come out from the crimp.
 (15) Cut the polyimide tape at approx.1 mm (0.0393 in.) from the ferrule.
 (16) Put the post-insulated sleeve on the crimped ferrule.
 ____NOTE : You must engage the bonding wire through the sleeve.
 (17) Crimp the assembly.
R R  ____NOTE : The crimped sleeve must not be on top of the ferrule that you crimped at step 5.

 

 Crimp Sleeves/Ferrules - Installation NSA937504 R Figure 006

20-42-22 Page 11

 Crimp Sleeves/Ferrules - Installation NSA937504 R Figure 007

20-42-22 Page 12

R ________________
4. Allocation table R (Ref. Fig. 002)

20-42-22 Page 13

 ____________________________________________________
SLEEVES - IDENTIFICATION - DESCRIPTION AND OPERATION
 _______
1. General
 High and low temperature identification sleeves installed on aircraft have the codes that follow: E0646 high temperature sleeve (ex NSA937204) NSA937201 high and low temperature sleeves NSA937202 low temperature sleeves NSA937203 low temperature sleeves taken from NSA937202 MC0300 sleeve
 __________________________________2. Identification and characteristics
 A. E0646 (ex NSA937204)
 (1) P/N Identification
 NSA937204  MF  15  A1
 E0646
 |  |  |  |
 |  |  |  ------------- Code marked on sleeve
 |  |  |
 |  |  ----------------- Type code
 |  |

 | --------------------- Type and color code | ----------------------------- Standard P/N
 (2)
 Characteristics

 (a)
 Color The sleeve color is yellow.

 (b)
 Diameter code (Ref. Fig. 001)

 (c)
 Marking Numbers 6 and 9 are underlined to prevent confusion.

 

 (3)
 Allocation table (Ref. Fig. 002)

 B. NSA937201
 (1) P/N Identification

20-42-31 Page 1

 Identification Sleeves - Characteristics
 NSA937201
 Figure 001

 

20-42-31 Page 2

 Identification Sleeves - Allocation Table for Wires
 E0646 and NSA937204
 Figure 002

 

20-42-31 Page 3

 NSA937201  MA  02  00
 |  |  |  |
 |  |  |  ------------------ Color code
 |  |  |
 |  |  ---------------------- Inner diameter code
 |  |
 |  -------------------------- Type code
 |

 ---------------------------------- Standard P/N
 (2)
 Characteristics

 (a) Type code (Ref. Fig. 003)
 -Type code
 (b) Color (Ref. Fig. 004)
 -Color code
 -For pink sleeves use black characters for sensitive lines.
 (c) Diameter code and shrinking tools (Ref. Fig. 003, 004)

 (3)
 Marking

 (a) For type codes ME, MG, MH and MD, use TMS90 system:
 -
In non SKYDROL areas, you must do 1 print and 2 permatisings.

 -
In SKYDROL areas, you must do 3 prints and 2 permatisings.

 (b) For type codes MR, MT, MK and ML, use SIX system (with ZEBRA 140 printer):
 -After printing, no permatising is necessary.
 -Make sure that the printing is resistant and that you can read it.

 (4)
 Allocation table (Ref. Fig. 005, 006, 007, 008, 009, 010, 011, 012)

 C. NSA937202
 (1) P/N Identification

20-42-31 Page 4

 Identification Sleeves - Inner Diameter Code
 E0646, NSA937202, NSA937203 and NSA937204
 Figure 003

 

20-42-31 Page 5

 Identification Sleeves - Color code and Tools
 NSA937201
 Figure 004

 

20-42-31 Page 6

 Identification Sleeves - Allocation Table for Terminals
 NSA937201
 Figure 005

 

20-42-31 Page 7

 Identification Sleeves - Allocation Table for Wires
 NSA937201
 Figure 006

 

20-42-31 Page 8

 Identification Sleeves - Allocation Table for Wires
 NSA937201
 Figure 007

 

20-42-31 Page 9

 Identification Sleeves - Allocation Table for Wires
 NSA937201
 Figure 008

 

20-42-31 Page 10

 Identification Sleeves - Allocation Table for Wires
 NSA937201
 Figure 009
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 2(95)