(2)  
A00964 Primer - BMS 10-11

 (3)  
D00153 Hydraulic fluid - BMS 3-11

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-81
 ALL  ú ú 01 Page 403 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 B.
C.
D.
A
737-300/400/500MAINTENANCE MANUAL
 (4)  
G01395 Corrosion Inhibiting Compound - BMS 3-27, Mastinox 6856K

 (5)
G50136 Corrosion Inhibiting Paste - BMS 3-38 (CORBAN 27L)References

 (1)  
AMM 07-11-31/201, Jack Airplane Axles

 (2)
AMM 29-15-00/001, Hydraulic SystemsAccess

 (1)  
Location Zone 310 Left Main Landing Gear 410 Right Main Landing Gear

Procedure
 S 424-020
 (1)  
Put the apex thrust washer (11) between the torsion links.

 S 424-021

 (2)  
Install the washer on the end of the lower torsion link (15) with the concave side of the washer against the link.

 S 614-001
 WARNING:_______DO NOT GET HYDRAULIC FLUID ON YOU. HYDRAULIC FLUID, BMS 3-11, CAN CAUSE INJURY TO PERSONS. IF YOU GET THE HYDRAULIC FLUID ON YOUR SKIN, FLUSH YOUR SKIN WITH WATER. IF YOU GET THE HYDRAULIC FLUID IN YOUR EYES, FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. IF YOU EAT OR DRINK THE HYDRAULIC FLUID, GET MEDICAL AID.
 CAUTION: USE CLEAN HYDRAULIC FLUID AND CLEAN EQUIPMENT WHEN YOU FILL THE
_______ DAMPER. DIRT CAN CAUSE DAMAGE TO THE HYDRAULIC SYSTEM.
 CAUTION:_______DO THIS PRE-FILL STEP. AIR CAN BE TRAPPED IN THE DAMPER IF IT IS NOT FULL OF HYDRAULIC FLUID. THE DAMPER WILL NOT WORK PROPERLY IF AIR IS TRAPPED IN IT.
 (3)  
Make sure that the damper assembly (13) is full of hydraulic fluid.

 (a)  
Remove the bleed plugs (16), (17) from the manifold (18).

 (b)  
Add fluid in the open ports (16) and (17) of the manifold (18) until they are all full.

 (c)  
Install the bleed plugs (16) and (17) in the manifold (18) ports.

 (4)  
Turn the inner cylinder.

 S 844-018
 NOTE: It is necessary to extend the torsion links to turn the inner
____ cylinder. Apply a forward and an aft force to the wheels to extend the torsion links.
 S 844-019
 (5)  Align the ends of the torsion links.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-81
 ALL  ú ú 01 Page 404 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 624-065
 WARNING: USE NITRILE GLOVES TO PROTECT YOUR SKIN FROM BMS3-27
_______ (MASTINOX 6856K). IF MASTINOX GETS ON YOUR SKIN, IMMEDIATELY REMOVE IT WITH WATER. IF THIS MATERIAL GETS IN YOUR EYES, IMMEDIATELY FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURIES TO PERSONS.
 CAUTION: REMOVE ALL UNWANTED MASTINOX FROM ALL THE SURFACES THAT WILL BE
_______ LUBRICATED. IF YOU APPLY MASTINOX TO THE JOINTS THAT TURN, FAILURE OF THE LANDING GEAR TO EXTEND OR RETRACT CAN OCCUR.
 (6)  
Apply a thin layer of BMS 10-11, Type 1 primer or, as an alternative, BMS 3-27 (MASTINOX) or BMS 3-38 (CORBAN 27L) corrosion inhibiting compound to the items that follow:

 (a)  
The mating surfaces between the damper assembly (13), and the upper torsion link (1).

 NOTE: Make sure the main gear damper shaft has no primer or
____ corrosion inhibiting compound on it.
 (b)  
To all the areas of the holes for the damper attachment bolts (3), and the damper bracket bolt.

 (c)  
The threads of the damper attachment bolts (3), and the damper bracket bolt.

 S 424-023
 (7)  
Do these steps to install the damper assembly (13):

 (a)  
Install the damper assembly (13) with the damper piston shaft through the upper torsion link (1), the apex thrust washer (11), and the lower torsion link (15).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(106)