G.
Procedure to Remove the Main Landing Gear
S 034-147
(1)
Disconnect the main gear lower side strut (1) from the side strut universal (2), (Fig. 403).
(a)
Remove the bolt (5).
(b)
Disconnect the lower end of the lower side strut (1) from the side strut universal (2), (Fig. 403). 1) Let the strut hang from the center pivot.
S 024-124
(2)
If the right main landing gear is to be removed, disconnect the interlock valve cable of the ground spoiler (AMM 27-62-51/401).
S 024-195
(3)
Remove the downlock springs (1), (Fig. 404).
(a)
Decrease the spring load on the attachment points of the downlock springs (1), (Fig. 404). 1) Attach a cord to the inboard end of the downlock spring (1)
and put it over the uplock support shaft (5).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-00
ALL ú ú 01 Page 405 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
1. ACTUATOR WALKING BEAM HANGER
12. ACTUATOR
11. TRUNNION LINK HYDRAULIC SWIVEL
10. TRUNNION LINK
UPPER DRAG STRUT
9. ELECTRICAL HARNESS
8. CLAMPS
7. HYDRAULIC
LINES
6. DAMPER HYDRAULIC LINE CONNECTION
5. MAIN GEAR DAMPER
FWD
A
737-300/400/500MAINTENANCE MANUAL
2. ACTUATOR WALKING BEAM
SEE A
WALKING BEAM ARM
SHOCK STRUT
3. BRACKET
LOWER DRAG STRUT
4. LINKS
INBD
11. HYDRAULIC
SWIVEL
FWD
A
Main Gear Components
Figure 402
10. TRUNNION LINK
HYDRAULIC
LINE
11. HYDRAULIC SWIVEL
13. DOOR ACTUATOR FITTING
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-00
ALL ú ú 01 Page 406 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
2) Pull the cord to extend the downlock springs (1).
(b) Disconnect the downlock springs (1) from their outboard attachments (Fig. 404).
S 024-022
(4)
Disconnect the reaction link universal (3) from the trunnion pin (6), (Fig. 404).
(a)
Put the reaction link (4) in a position so that it does not touch the shock strut.
S 024-196
(5)
Disconnect the trunnion link (7) from the shock strut (3), (Fig. 406).
(a)
Put chocks on the aft side of the wheels, (Stage 1, Fig. 405).
(b)
Hold the gear in position by hand.
(c)
Remove the antirotation bolt (1) from the actuator walking beam arm (2), (Fig. 406).
(d)
Remove the nuts and the washers from the trunnion pin lockbolts (4).
(e)
Use an adapter wrench and remove the trunnion pin nut (6).
(f)
Remove the retainer washer (5) and the special washer (5A) from the trunnion pin (9).
(g)
Install the thread protector (8) on the trunnion pin (9).
(h)
Remove the trunnion pin (9) with light hits from a lead hammer.
1. LOWER SIDE
5. BOLT STRUT
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-00
ALL ú ú 01 Page 407 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
2. SIDE STRUT
UNIVERSAL
3. UPPER
DRAG
INBD FWD STRUT
SEE A
4. LOWER
DRAG
STRUT
INBD FWD
A
Main Gear Side Strut Lower Attachment
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(45)
