(a)
Move a spare static seal O-ring (9) from the lower spare seal recess in the lower bearing (7). 1) Apply a layer of hydraulic oil and a light layer of
petrolatum before the O-ring installation.
(b)
Carefully pull the lubricated spare static O-ring seal (only enough to install the O-ring in the groove of the seal adapter (4)).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-21
ALL ú ú 01 Page 804 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
17. OUTER CYLINDER
15. BACKUP RINGS
SEE A
A
A 737-300/400/500MAINTENANCE MANUAL
1.
LOCKPLATE
2.
SPACER
3.
ACTIVE STATIC SEAL O-RING
4.
SEAL ADAPTER
21. ACTIVE DYNAMIC SEAL
6.
WASHER
7.
LOWER BEARING
8.
SPARE DYNAMIC SEAL
9.
SPARE STATIC SEAL O-RINGS
10.
SCRAPER RING
11.
SCRAPER RING ADAPTER
12.
GLAND NUT
16. INNER CYLINDER
DRAIN TUBE
14. CHECK VALVE
SEAL CAP
SHOCK STRUT A
Main Gear Shock Strut Seal Replacement Figure 801 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-21
ALL ú ú 01 Page 805 ú Feb 20/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
17. OUTER
SEE
Main Gear Shock Strut Seal Replacement
Figure 801 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-21
ALL ú ú 01 Page 806 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
INCHES STROKE,
13.856-13.983 1
14.856-14.983 2
FULLY COMPRESSED POSITION
737-300 AND 737-500 AIRPLANES 737-400 AIRPLANES
FULLY EXTENDED POSITION
Main Landing Gear Shock Strut Replacement
Figure 801 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-21
ALL ú ú 01 Page 807 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F40490
A
737-300/400/500MAINTENANCE MANUAL
(c) Install a new backup ring on each side of the O-ring.
NOTE: O-rings must have no twists when installed.
____
(d)
Move a spare dynamic seal assembly (8) from the higher spare seal recess in the lower bearing (7). 1) Apply a layer of hydraulic oil and a light layer of
petrolatum before installation.
(e)
Move a spare dynamic seal assembly up the inner cylinder into the recess in the seal adapter. 1) Move the lower bearing (7) and washer (6) against the seal
to hold the seal in its position.
(f)
Move the bearing and the seal adapter as a unit on the outer cylinder.
(g)
Move the scraper adapter (11) with the scraper ring (10) into their position against the lower bearing.
S 438-019
(7) Install the Gland Nut
WARNING: USE NITRILE GLOVES TO PROTECT YOUR SKIN FROM BMS 3-27
_______ (MASTINOX 6856K). IF MASTINOX GETS ON YOUR SKIN, IMMEDIATELY REMOVE IT WITH WATER. IF THIS MATERIAL GETS IN YOUR EYES, IMMEDIATELY FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURIES TO PERSONS.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(77)
