S 032-032
(2)
Remove the quadrant (1) from the programmer (14, 21) (Fig. 201):
(a)
Remove the nut (49) and the washer (50) from the quadrant shaft (42) (detail H).
(b)
Remove the quadrant retaining bolt (44).
(c)
Remove the cover (43) from the programmer (14, 21).
(d)
Remove the shaft (42) from the programmer (14, 21).
(e)
Remove the quadrant (1).
S 352-033
(3) Repair the quadrant:
CAUTION:_______DO NOT MAKE THE RIVET HOLES LARGER. THIS CAN CAUSE DAMAGE TO THE QUADRANT.
(a)
Remove the broken part of the rivets (53) from the holes in the quadrant (1) and the coupling (52).
(b)
Install the new shear rivets (53).
NOTE: The aluminum foil marker on the quadrant has the correct
____ rivet numbers that you must use for the installation.
S 432-034
(4)
Install the quadrant (1) on the programmer (14 and 21):
(a)
Put the shaft (42) through the quadrant coupling (52).
(b)
Install the nut (49), washer (50) and cotter pin (51) on the shaft (42).
(c)
Engage the splines of the quadrant coupling and shaft (42).
(d)
Install the retaining bolt (44), washer (45), nut (46), and cotter pin (47).
(e)
Install the cover (43).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-10
ALL ú ú 03 Page 213 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 422-035
(5) Install the aileron programmer (14, 21) (par. 3).
TASK 27-11-10-202-036
5. Aileron Programmer Inspection/Check___________________________________
A. General
(1)
This procedure contains the task to do the inspection/check of the aileron programmer.
(2)
The Aileron Programmer Inspection/Check examines the worn areas of the bearing/bolt (54) and the cam/bushing (55). If a replacement is necessary, refer to the removal and installation procedure of the aileron programmer.
B.
Standard Tools and Equipment
(1)
Micrometer, to measure internally and externally
C. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 201 | 14 | Aileron Programmer (RH) | 27-11-08 | 01 | 525 | | | 21 | Aileron Programmer (LH) | | | 520 | | | 54 | Bearing/Bolt | | | | | | | Bearing | 27-11-10 | 01 | 195 | | | | Bolt | | | 180 | | | 55 | Cam /Bushing | | | | | | | Cam | 27-11-10 | 01 | 170 | | | | Bushing | | | 165 | 2......…........…...................................…...........….....…........1
D. References
(1)
Paragraph 2. through 3.
E.
Access
(1)
Location Zone
135 Wing Landing Gear Well, LH
136 Wing Landing Gear Well, RH
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-10
ALL ú ú 03 Page 214 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
F. Do a Check of the Aileron Programmer
S 022-037
(1)
Remove the aileron programmer (14 and 21) (par. 2).
S 222-038
(2)
Do a check of the aileron programmer (Fig. 201).
(a)
Remove the parts (54 and 55) to be examined.
(b)
Measure the dimensions of the parts.
(c)
Compare these part dimensions to the limit dimensions.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(127)
