S 014-004
 (4)
Get access to cables AA and AB on the right or left side.

 (a)  
Do this task to get access above the seals: "Floor Panel Removal" (AMM 53-21-02/401).

 NOTE: The floor panels you remove are above the ceiling of
____ wheel well for the wing landing gear. It is approximately 6 feet to the right or the left of the keel beam and aft of STA 1245.
 (b)  
Get access below the seals from the wheel well for the wing landing gear.

 E.
Remove the Aileron Raised Control Cable Air Pressure Seal

 S 034-005
 (1)  Disconnect the control cables at the turnbuckles adjacent to the input quadrant.
 NOTE: A light tension on the cable at all times is necessary while
____ the cable is disconnected. This will keep the cable on the cable pulleys.
 S 034-072
 (2)  
Remove the air pressure seal (Fig. 401):

 (a)  
Remove the two seal retaining bolts, nuts, and washers.

 (b)  
Remove the seal plate and the seal cover from the top and bottom surface of the pressure deck.

 (c)  
Cut the shrink sleeve from the seal.

 (d)  
Remove the seal halves from the control cable.

 (e)  
Remove the seal from the hole in the pressure deck.

 (f)  
Remove the seal from the cable.

 TASK 27-00-02-404-085
 3. Aileron Raised Control Cable Air Pressure Seal Installation
___________________________________________________________
 A. Special Tools and Equipment
 (1)  
G12001-50 Rig Pin Kit

 B.
Consumable Materials

 (1)  
D00015 Grease - Corrosion Preventive, BMS 3-24

 C.
References

 (1)  
AMM 20-11-25/201, Heat Gun, Soldering Guns and/or Soldering Irons

 (2)  
AMM 27-11-00/501, Aileron and Aileron Trim Control System

 (3)  
AMM 29-11-00/201, Main Hydraulic Supply System

 (4)  
AMM 53-21-02/401, Main and Upper Deck Floor

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-00-02
 ALL  ú ú 01 Page 402 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
SBA-2 TURNBUCKLES
SBB-2
AA-3 AB-3
AB-4
AA-4
REAR SPAR CANTED PRESSURE BULKHEAD
CENTRAL LATERAL CONTROL PACKAGE
CONTROL ACABLE
TUBE
A
PRESSURE SEAL
TUBE
CONTROL
CABLE
BOLT 
WHEEL WELL SIDE OF  (2 LOCATIONS)  HALF SEAL 
BULKHEAD  COVER AND PLATE  PRESSURE 
SHRINK  APPLICATION 
USUAL SEAL INSTALLATION  SLEEVE  POINT (TWO SIDES) 
A-A 

Aileron and Speedbrake Control Cable Raised Seal Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-00-02
 ALL  ú ú 01 Page 403 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 D. Access
 (1)  
Location Zone
 241 Passenger Cabin, Left Side
 242 Passenger Cabin, Right Side

 E.
Install the Aileron Raised Control Cable Air Pressure Seal

 S 644-011
 (1)  Lubricate the cable with grease for the full length of travel of the seal.
 NOTE: Do not fill the seal with grease.
____
 (a)  Remove the unwanted grease from the cable.
 S 434-076
 (2)  
Install the air pressure seal (Fig. 401):

 (a)  
Push the tube through the seal plate.

 (b)  
Make sure the smaller gasket of the seal plate is against the spherical end of the tube.

 (c)  
Put the shrink sleeve on the tube.

 (d)  
Install the cable end through the tube assembly with the spherical end of the tube pointed down.

 NOTE: A rigid wire attached to the cable end can make for
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(24)