C. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 2 | Washer | 27-11-01 | 02 | 40 | | | 3 | Nut | | | 45 | | | 4 | Washer | | | 40 | | | 5 | Bolt | | | 35 | | | 6 | Washer | | | 60 | | | 7 | Nut | | | 65 | | | 9 | Jumper | | | 10 | | | 10 | Washer | | | 55 | | | 11 | Bolt | | | 50 | | | 12 | Bushing | | | 115 | | | 13 | Washer | | | 105 | | | 14 | Nut | | | 110 | | | 16 | Washer | | | 100 | | | 17 | Bolt | | | 95 | | | 18 | Nut | | | 90 | | | 19 | Washer | | | 80 | | | 20 | Bushing | | | 85 | | | 21 | Antirotation Plate | | | 120 | | | 22 | Washer | | | 135 | | | 23 | Nut | | | 140 | | | 25 | Washer | | | 130 | | | 26 | Bolt | | | 125 | | | 28 | Bolt | 27-11-12 | 02 | 80 | | | 29 | Bushing | | | 97 | | | 30 | Antirotation Plate (LH) | | | 120 | | | 30 | Antirotation Plate (RH) | | | 125 | | | 31 | Bolt | | | 100 | | | 32 | Washer | | | 105 | | | 33 | Nut | | | 115 | | | 34 | Antirotation Plate (LH) | | | 175 | | | 34 | Antirotation Plate (RH) | | | 180 | | | 35 | Bolt | | | 150 | | | 36 | Washer | | | 145 | | | 37 | Bolt - Outer | | | 140 | | | 38 | Retaining Ring | | | 160 | | | 39 | Reaction Linkage | | | 245 | | | 40 | Bolt - Inner | | | 135 | | | 41 | Nut | | | 170 | | | 42 | Washer | | | 165 | | | 43 | Nut | | | 95 | | | 44 | Washer | | | 90 | | | 45 | Retaining Ring | | | 75 | 2......…........…...................................…...........….....…........1
D. References
(1) AMM 06-09-08/201, Wing Access Doors and Panels
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-01
ALL ú ú 01 Page 408 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(2)
AMM 12-21-16/301, Aileron and Aileron Trim Control
(3)
AMM 24-22-00/201, Manual Control
(4)
AMM 27-11-01/601, Inboard Aileron
(5)
AMM 29-11-00/201, Main Hydraulic Supply System
(6)
SSM 27-11-01
(7)
WDM 27-11-11
E.
Access
(1)
Location Zones
579 Inboard Aileron, LH
679 Inboard Aileron, RH
(2)
Access Panels 573AB Inboard Aileron Actuator, Lower Wing Surface, LH 573BB Inboard Aileron Actuator, Lower Wing Surface, LH 673AB Inboard Aileron Actuator, Lower Wing Surface, RH 673BB Inboard Aileron Actuator, Lower Wing Surface, RH 573CB Hydraulic Access Panel (LI Transmitter) 673CB Hydraulic Access Panel (RI Transmitter)
F.
Prepare for Installation
S 214-054
(1)
Adjust the wing trailing edge bulb seal if upper surface of leading edge on the left and right inboard ailerons show signs of chafing, and/or the seal compression is greater than 10 percent when in contact with the inboard aileron. Do the steps that follow (Fig. 403):
(a)
Remove the seal retainer assembly from the wing fixed trailing edge panel.
(b)
Increase the hole size of the slot in the bulb seal and seal depressor in the aft direction a maximum of 0.06 inch.
(c)
Repair surface preparation to the seal depressor using Alodine 1200.
(d)
Install the seal retainer assembly with the steps that follow:
1) Adjust the position of the assembly keeping a seal compression of 1 to 10 percent for any inboard aileron position.
NOTE: The seal compression must be constant for all
____ aileron position.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-11-01
ALL ú ú 01 Page 409 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
2) Make sure there is a minimum clearance of 0.05 inch between the retainer and the honeycomb core.
(e)
If the chafing damage is forward of the aileron front spar and the depth does not go completely through the outer 0.010-inch thick bonded skin, refinish the surface by applying Alodine 1200 and BMS 10-11, Type I.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(75)
