(c)
Remove rig pin R-5.
(d)
Attach a phase angle voltmeter directly to the transmitter connector or through a syncro breakout box.
(e)
Make sure that the transmitter is electrically nulled (0.0 degree angle) position within 50 milivolts by applying 26 VAC 400 Hz to pins 1 and 2 and measuring voltage at pins 4 and 5 using the phase angle voltmeter.
NOTE: The transmitter reading may be verified using the EICAS
____ display, accessible thru the MCDU and show a reading of 0 +/-.2 degrees.
(f)
If the transmitter is not nulled rotate the adjustment knob on the control rod until the transmitter is nulled. Do not rotate the adjusment knob more than two turns clockwise from its original position.
(g)
Make sure the transmitter is nulled and has not changed.
(h)
Remove rig pin R-3.
(i)
Remove electrical power if not needed (AMM 24-22-00/201).
F.
Do a Check of the Transmitter
S 714-009
(1)
Examine the movement of the transmitter:
(a)
Push the left rudder pedal forward to stop.
(b)
Make sure that the PEDAL indication on the EICAS flight controls maintenance page shows 21.1-21.9 degrees left.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-08-02
ALL ú ú 12 Page 405 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(c) (d) (e) Push the right rudder pedal forward to stop.Make sure the PEDAL indication shows 21.1-21.9 degrees right.Release the rudder pedals.
(2) S 414-010Do this task to install the ceiling panel that you removed for access: "Install the Zone A Center Trough" (Ref 25-22-01/401).
(3) S 864-014Do this task: "Remove Electrical Power" (Ref 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-08-02
ALL ú ú 11 Page 406 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
CONTROL COLUMN POSITION TRANSMITTER - REMOVAL/INSTALLATION
__________________________________________________________
1. General_______
A. This procedure has two tasks, one for the removal and one for the installation of the control column position transmitter (which is referred to as the "transmitter"). The procedure has these parts:
(1)
The removal of the transmitter
(2)
The installation of the transmitter
(3)
An adjustment of the transmitter
(4)
An operational test of the transmitter.
TASK 27-08-03-004-001
2. Control Column Position Transmitter Removal (Fig. 401)___________________________________________
A. References
(1)
25-22-01/401, Main Passenger Compartment Ceiling Access Panels
(2)
IPC 27-31-04 Fig. 3
(3)
SSM 27-09-05
(4)
WDM 27-09-31
(5)
WDM 20-90-11
B.
Access
(1)
Location Zone 211 Passenger Cabin - Nose to First Door, LH
C.
Procedure
S 864-002
(1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6 Main Power Distribution Panel
1) 6J22 COL/RUD PEDAL SENSOR
2) 6J23 COL/RUD PEDAL IND
S 014-003
(2) Do this task to remove the left main deck ceiling panel at station
297: "Remove the Zone A Center Trough" (Ref 25-22-01/401).
S 024-031
(3)
Remove the transmitter:
(a)
Remove the wire clamp from the transmitter.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 1(33)
