(a)  
Install a tag on the cables for identification during the installation.

 S 024-014
 (12)
 Remove the rudder aft quadrant (Fig. 402):

 (a)  
Disconnect the input control rod from the quadrant crank.

 (b)  
Remove the nut, washer and bolt that attach the aft quadrant to the support bracket (Section A-A).

 (c)  
Remove the aft quadrant.

 TASK 27-21-08-404-015
 3.  Rudder Aft Quadrant Installation________________________________
 A. Special Tools and Equipment
 (1)  
G12001-50 Rig Pin Kit

 (2)  
2MIT65B04011-41 Nose Gear Rig and Tow Safety Pin

 B.
Consumable Materials

 (1)
C00174 Corrosion Preventive Compound - MIL-C-16173, Grade 2

 (2)
C00308 Corrosion Preventive Compound - MIL-C-11796, Class 3

 C.
References

 (1)  
09-11-00/201, Towing

 (2)  
24-22-00/201, Manual Control

 (3)  
25-22-01/401, Main Passenger Cabin Ceiling Panel

 (4)  
27-21-08/601, Rudder Aft Quadrant

 D.
Access

 (1)  
Location Zone 211 Passenger Cabin-Nose to First Door, LH 311 Area Aft of Pressure Bulkhead, LH 312 Area Aft of Pressure Bulkhead, RH 323 Vertical Stabilizer, Front Spar to Rear Spar 324 Vertical Stabilizer, Rear Spar to Trailing Edge

 (2)  
Access Panels 312A Horizontal Stabilizer Jackscrew Access Door 324FR Centering Mechanism Access Panel 324FL Centering Mechanism Access Panel

 E.
Procedure

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-08
 ALL  ú ú 01 Page 406 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 494-016
 WARNING:_______ MAKE SURE THE NOSE WHEELS POINT FORWARD.  IF THE NOSE WHEELS DO
 NOT POINT FORWARD, THE NOSE GEAR CAN QUICKLY TURN TO THE
 CENTERED POSITION WHEN YOU REMOVE THE TOW PIN.  THIS CAN CAUSE

 INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  Install the TOW PIN at the steering metering valve for the nose landing gear (Ref 09-11-00/201).
 NOTE: The nose gear will turn during the rudder operation if you
____ do not install the TOW PIN.
 S 224-017
 (2)  
If you will install used parts, examine the parts for worn areas (Ref 27-21-08/601).

 S 424-018

 (3)  
Install the rudder aft quadrant (Fig. 402):

 (a)  
Put the rudder aft quadrant in its position on the support bracket.

 (b)  
Install the bolt, bolt, washers, and nut to attach the aft quadrant to the support bracket (Section A-A).

 (c)  
Tighten the nut.

 (d)  
Turn the quadrant to make sure it moves easily.

 (e)  
Connect the cables RA and RB to the aft quadrant: 1) Put the cables on the aft quadrant. 2) Install the cable retainers with the screws, washers and

 nuts.

 (f)  
Connect the input rod to the input crank with the bolt, washer and nut.

 S 834-036
 (4)  
If you installed new control cables RA and RB:

 (a)  
Tighten the turnbuckles on the cables RA and RB equally until the tension is 250 |20 pounds.

 (b)  
Remove the rig pins R-3 and R-4.

 (c)  
Operate the rudder control pedals 25 times.

 (d)  
Install the rig pins R-3 and R-4.

 S 834-023
 (5)  
Adjust the rudder control cables RA and RB:

 (a)  
Adjust the two turnbuckles equally to get the tension in the cables RA and RB to the tension shown in Fig. 403.

 (b)  
Make sure you can easily install and remove the rig pins R-3 and R-4.

 (c)  
Remove the rig pins R-3 and R-4.

 (d)  
Operate the rudder control pedals through one full cycle.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-08
 ALL  ú ú 01 Page 407 ú Oct 10/91
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(100)