27-21-07
 ALL  ú ú 01 Page 404 ú Feb 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 024-037
 (11)
 Remove the rudder pedal assemblies.

 (a)  
Remove the nuts from the two ends of the rudder pedal support shaft (Fig. 401).

 (b)  
Hold the two rudder pedal assemblies and remove the support shaft through the floor structure.

 (c)  
Lift the two rudder pedal assemblies up through the cabin floor.

 TASK 27-21-07-404-008
 3.  Rudder Pedal Assembly Installation (Fig. 401)__________________________________
 A. Special Tools and Equipment
 (1)  
G12001-50 Rig Pin Kit

 (2)  
2MIT65B04011-41 Nose Gear Rig and Tow Safety Pin
 (referred to as the TOW PIN)

 B.
Consumable Materials

 (1)
C00174 Compound, Corrosion Preventive - MIL-C-16173, Grade 2

 C.
References

 (1)  
AMM 09-11-00/201, Towing

 (2)  
AMM 24-22-00/201, Manual Control

 (3)  
AMM 27-21-07/601, Rudder Pedal Assembly

 (4)  
AMM 32-41-00/501, Brake Hydraulic System

 (5)  
AIPC 27-21-07 Fig. 1

 D.
Access

 (1)  
Location Zone
 221 Control Cabin, LH
 222 Control Cabin, RH
 211 Passenger Cabin-Nose to First Door, LH
 212 Passenger Cabin-Nose to First Door, RH

 E.
Procedure

 S 494-009
 WARNING:_______MAKE SURE THE NOSE LANDING GEAR IS POINTED FORWARD. IF THE TIRES ARE NOT PARALLEL WITH THE AIRPLANE, THEY CAN TURN QUICKLY WHEN YOU REMOVE THE TOW PIN. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  Install the TOW PIN at the steering metering valve on the nose landing gear (AMM 09-11-00/201).
 NOTE: This is to make sure the nose landing gear does not turn.
____
 S 224-010
 (2)  Do a check of the wear limits for the rudder pedal assembly (AMM 27-21-07/601).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-07
 ALL  ú ú 04 Page 405 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 424-011
 (3)  Install the rudder pedal assembly in the floor structure.
 (a)  Apply a layer of corrosion preventive compound to the support
 shaft for the rudder pedals.
 (b)  Hold the two rudder pedal assemblies in their positions in the
 floor structure.
 (c)  Install the support shaft through the floor structure and the
 rudder pedal assemblies from the outboard side.
 (d)  Tighten the nuts on the support shaft to 100 to 125
 pound-inches more than the nut run-on torque.
 S 494-012
 (4)  Install the rig pin R-3 in the forward quadrant.
 S 414-038
 (5)  Put the upper cover assembly, with the flexshaft attached, on the
 floor above the rudder pedals (Fig. 402).
 NOTE:____ Do not install the screws in the cover.

 S 434-039
 (6)  
Connect the flexshaft to the forward quadrant jackshaft.

 (a)  
Put the flexshaft in its position aft of the jackshaft.

 (b)  
Put the washer and the shaft retaining nut on the end of the flexshaft.

 (c)  
Put the flexshaft into the jackshaft and turn it until it engages the pin in the jackshaft.

 (d)  
Tighten the shaft retaining nut.

 S 414-040
 (7)  
Install the screws that connect the upper cover assembly of the rudder pedal to the support structure.

 S 414-048

 (8)  
Install the cover extension.

 S 864-041

 (9)  
Put the rudder pedals in their center position with these steps:

 (a)  
Use the adjustment crank to move the rudder pedals to their fully forward position.

 (b)  
Turn the adjustment crank back 6.5 turns from the fully forward position.

 S 424-043
 (10)
 Connect the quadrant pushrods to the rudder pedal arms.

 (a)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(95)