27-18-00
ALL ú ú 01 Page 504 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 495-019
(7)
Install the rig pin through the crank and the inner rig pin hole of the bracket.
S 835-020
(8)
Do this adjustment of the aileron position indicating system:
(a)
For the outboard aileron, make sure the indication on the EICAS flight controls maintenance page is 0.6 | 0.1 degree down. 1) If the indication is out of the tolerance, adjust the control rod until it shows 0.6 | 0.1 degree down.
(b)
For the inboard aileron, make sure the indication on the EICAS flight controls maintenance page is 0 | 0.2 degree. 1) If the indication is out of the tolerance, adjust the
control rod until it shows 0 | 0.2 degree.
(c)
If you can not adjust the control rod to zero, adjust the transmitter body in the bracket: 1) Move the rig pin to the outer hole.
NOTE: You may need to adjust the control rod to install
____
the rig pin.
2) Loosen the transmitter clamping screws. 3) Adjust the transmitter body until you get the necessary tolerance.
4) Tighten the transmitter clamping screws to 5-10 pound-inches. a) Make sure you do not turn the transmitter body.
(d)
If the indication is not in the tolerance, adjust the control rod: 1) Move the rig pin to the inner hole. 2) Adjust the control rod.
(e)
Install the lockwire on the thumb nut of the control rod.
(9)
Remove the rig pin from the transmitter assembly.
S 095-021
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-18-00
ALL ú ú 01 Page 505 ú Feb 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 415-022
(10)
Close the access panel.
S 865-027
(11)
Do this task: "Trailing Edge Flap Activation" (AMM 27-51-00/201).
S 865-025
(12)
If the electrical power is not necessary, do this task: "Remove Electrical Power" (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-18-00
ALL ú ú 01 Page 506 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
AILERON POSITION TRANSMITTER - REMOVAL/INSTALLATION
___________________________________________________
1. General_______
A. There are two tasks in this procedure. There is one task for the removal and one task for the installation of the aileron position transmitter. The procedure has these parts:
(1)
The removal of the aileron position transmitter
(2)
The installation of the replacement transmitter
(3)
The adjustment of the transmitter.
TASK 27-18-01-004-001
2. Aileron Position Transmitter Removal (Fig. 401)____________________________________
A. References
(1)
AMM 27-51-00/201, Trailing Edge Flap System
(2)
AIPC 27-18-01, Fig. 1
(3)
SSM 27-18-01
(4)
WDM 27-18-11
B.
Access
(1)
Location Zone 591 Rear Spar to Trailing Edge, LH at Outboard Aileron 573 Rear Spar to Trailing Edge, LH at Inboard Aileron 673 Rear Spar to Trailing Edge, RH at Inboard Aileron 691 Rear Spar to Trailing Edge, RH at Outboard Aileron
(2)
Access Panel 591CB Outboard Aileron Access Panel (LO Transmitter) 573CB Hydraulic Access Panel (LI Transmitter) 673CB Hydraulic Access Panel (RI Transmitter) 691CB Outboard Aileron Access Panel (RO Transmitter)
C.
Procedure
S 864-019
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 2(34)
