(f)  
Connect the bonding jumper (20) to the rudder. 1) Use the milliohmmeter to make sure there is a maximum of

 0.01 ohms between the rudder and the vertical fin.
 (g)  
Install the bushings (24) (2 locations).

 (h)  
Install the bolt (23), the washers (33, 30), and the nut (28). Tighten the bolt to (23) 1300-2000 pound-inches.

 (i)  
Install the cotter pin (29).

 S 424-092
 WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR BELOW THE RUDDERS.
_______ OBJECTS CAN FALL AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (3)  
Do these steps to install hinge No. 7 or 8.

 (a)  
Apply corrosion preventive compound to the vertical fin, where the bearing assembly (1) will touch it.

 (b)  
Put the bearing assembly (1) in its position on the vertical fin.

 (c)  
Install the bolts (2), the washer (3), and the nut (4) (8 locations).

 (d)  
If the actuators were disconnected from the upper rudder, connect the actuators to the upper rudder (Ref 27-21-15/401).

 (e)  
Connect the bonding jumper (20) to the rudder.

 (f)  
Apply a thin layer of grease to the pins (34, 35), or (43, 44).

 (g)  
Install the pins (34, 35) in hinge No. 7, or the bushing (22) and the pins (43, 44) in hinge No. 8. Also, install the antirotation lug (36).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-03
 ALL  ú ú 03 Page 417 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (h)  
Tighten the threaded bushing(s) (12) with your hand until there is no clearance between the bushing and the bearing.

 (i)  
On hinge No. 7, install washers (42) until you get a 0.02-0.05 inch clearance between the bushings (12) and the washers.

 (j)  
Apply sealant to the mating surfaces of the washers (42) and the bushings (12).

 (k)  
Install the washer (18), and the nut (17). Also, install the washers (19) until the lockbolt (14) engages the nut (17) correctly. 1) Tighten the nut (17) to 2000-2400 pound-inches. 2) If it is necessary, tighten the nut (17) to a maximum of

 3200 pound-inches to let you install the lockbolt (14).

 (l)  
Install the washer (38), and the nut (40). Also, install the washers (39) until the cotter pin (41) engages the nut (40) correctly. 1) Tighten the nut (40) to 300-500 pound-inches.

 (m)  
Install the lockbolt (14), the washer (15), and the nut (16).

 (n)  
Install the cotter pin (41).

 S 864-119
 (4)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P7, Overhead Circuit Breaker Panel
 1) 7D16 RUD TRIM CONT

 (b)  
P180, DC Power Distribution Panel
 1) 180E7 ELEV/RUD VLV SYS 2
 2) 180E22 ELEV/RUD VLV SYS 4
 3) 180H8 ELEV/RUD VLV SYS 1
 4) 180H23 ELEV/RUD VLV SYS 3

 S 864-120
 (5)  
Find the switches for the FLT COLTROL HYD POWER on the Pilot's Overhead Maintenance Panel, P461.

 (a)  
Put the TAIL switches in the NORM position.

 H.
Rudder Hinge Movement Test

 S 494-080
 (1)  Install the rig pin in the steering metering valve for the nose landing gear (Ref 32-50-00/201).
 NOTE: Do this to make sure the nose landing gear does not move.
____
 S 864-121
 (2)  
Supply electrical power (Ref 24-22-00/201).

 S 864-122

 (3)  
Supply hydraulic power for systems No. 1 and 2, or 3 and 4
 (Ref 29-11-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-03
 ALL  ú ú 03 Page 418 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 714-123
 CAUTION:_______MOVE THE RUDDER PEDALS SMOOTHLY AND SLOWLY. THE MINIMUM TIME FOR A FULL CYCLE IS 8 SECONDS. IF YOU MOVE THE RUDDER PEDALS TOO FAST, THE POWER CONTROL PACKAGE CAN BE DAMAGED.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(85)