shock strut. 2) Do a check for the twisted seals or the clearance between the parts.

 (o)  
Install the gland nut lockplate (5) after all parts are assembled and tightened correctly.

 NOTE: If tilt sensor was moved to help install gland nut, do
____ Adjust the Truck Tilt Sensor for the Wing Gear procedure (AMM 32-61-22/201).
 J. Put the airplane back to its usual condition.
 S 118-028
 (1)  
Rub the open part of the inner cylinder with hydraulic fluid specified on the shock strut nameplate.

 S 588-029

 (2)  
Put the weight of the airplane back to the landing gear
 (AMM 07-11-01/201.

 S 618-030

 (3)  
Do the servicing of the shock strut for the wing landing gear (AMM 12-15-03/301).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-02
 ALL  ú ú 01A Page 817 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 938-031
 (4)  
Put a tab label on the shock strut.

 (a)  
The label shows "ONE SET SPARE SEALS USED" if there is one set of spare seals in the shock strut.

 S 938-032
 (5)  
Put a tab label on the shock strut.

 (a)  
The label shows "TWO SETS OF SPARE SEALS USED" if there are no spare seals in the shock strut.

 S 098-099
 WARNING: YOU MUST CAREFULLY DO THE STEPS BELOW TO REMOVE THE DOOR LOCKS
_______ FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (6)  
Do this task: "Removal of the Door Locks from the Wing Landing Gear" (AMM 32-00-30/201).

 S 098-111

 (7)  
Do this task: "Removal of the Door Locks from the Body Landing Gear" (AMM 32-00-30/201).

 TASK 32-11-02-368-116
 3. Lower Bearing Seals and Spare Seals Replacement (Fig. 805)
______________________________________________
 A. Special Tools and Equipment
 (1)  
MIT65B01201 - Gland Nut Wrench Adapter

 (2)  
G32011-1 Oversize Gland Nut Wrench Adapter (Airplanes with oversize gland nut)

 (3)  
7MIT65B01211-1 - Lower Gland Seal Split Guide

 (4)  
21MIT65B01211-1 - Gland Seating Tool, BG, WG, NG

 (5)  
2MIT65B01201 Lower Bearing Seal Retainer Puller

 (6)  
3MIT65B01201-1 Spanner Wrench, Pivot Pin Nut, Wing Landing Gear (Strut to Truck Beam).

 (7)  
8ME65B01202-3 Shock Strut Retention Tool

 B.
Standard Tools and Equipment

 (1)  
Plastic tool for cutting seal ring

 (2)  
Drip tray with 25-gallon minimum capacity

 (3)  
Cloth padding for inner cylinder surface protection

 (4)  
Nylon Sling 4000 pound capacity

 (5)  
Grease Gun

 C.
Consumable Materials

 (1)  
D00070 Oil, Hydraulic, Petroleum Base-MIL-H-5606

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-02
 ALL  ú ú 01A Page 818 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

NUT LUBE RETAINER BRAKE ROD BOLT BRAKE ROD TANG WASHER INNER CYLINDER YOKE 
O-RINGS  LOCKBOLT 
A  SEE  A  SEE  B 
INNER CYLINDER YOKE 
INBD  TRUCK PIVOT BOLT PIVOT LOCKBOLT LUBE INSERT NUT SPLINE WASHER 
PIVOT BOLT HEAD  TRUCK BEAM 
O-RINGS 
B 
Figure 805 Truck Beam Details for the Wing Landing Gear 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-02
 ALL  ú ú 01A Page 819 ú Jun 10/94
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 1(110)