曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

A
747-400 MAINTENANCE MANUAL
 WING GEAR UPPER JURY STRUT - ADJUSTMENT/TEST
____________________________________________
 1.  General_______
 A.  You must examine the alignment of the jury strut assembly after you install the upper or lower jury struts. If the alignment is incorrect, you must adjust the jury strut assembly. When you replace the assembly of the side strut component, an inspection of the alignment is not necessary.
 B.  The jury strut apex is correctly aligned when it is off-center. You can see this in Figure 501, View A-A.
 TASK 32-11-08-825-001
 2.  Jury Strut Adjustment (Fig 501)_____________________
 A.  Special Tools and Equipment
 (1)
2MIT65B08803-1 - Wing Landing Gear Bungee Restraining Tool

 B.  
Standard Tools and Equipment

 (1)
Steel straightedge, 4 foot

 (2)
Scale, graduated in 0.01 inch

 C.  
Consumable Materials

 (1)
D00633 Grease - BMS 3-33 (preferred)

 (2)
D00013 Grease - MIL-G-23827 (optional)

 D.  
References

 (1)
AMM 07-11-01/201, Jacking Airplane

 (2)
AMM 09-11-00/201, Towing

 (3)
AMM 29-11-00/201, Main Hydraulic Supply System

 (4)
AMM 32-00-30/201, Landing Gear Door Locks

 (5)
AIPC 32-11-08 Fig. 1

 (6)
AIPC 32-11-09 Fig. 1

 E.  
Access

 (1)  
Location Zone
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH

 F.  
Preconditions

 S 865-021
 (1)
These conditions are necessary for this task:

 (a)
The airplane is on jacks (AMM 07-11-01/201).

 (b)
The hydraulic power is off (AMM 29-11-00/201).

 G.  
Adjust the Jury Strut

 (1)
Install the ground locks for the landing gear (AMM 09-11-00/201).

 S 865-002
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-08
 ALL  ú ú 01 Page 501 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE A
SENSORS
STOP PLATE
BOLT (3)
A LOWER JURY STRUT
LOWER JURY STRUT UPPER JURY STRUT
A
SHIM
BARREL NUT (3)
APEX BOLT
FWD
JURY STRUT APEX 
A 
UPPER JURY 
STRUT 

A = 0.25 |0.02 INCH
JURY STRUT APEX BOLT CENTERLINE
OFF-CENTER DIMENSION
A-A
Wing Gear Jury Strut Adjustment
Figure 501

CENTERLINE UPPER JURY STRUT PIN/ LOWER JURY STRUT PIN
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-08
 ALL  ú ú 01 Page 502 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 495-003
 WARNING: YOU MUST REFER TO 32-00-30/201 FOR THE LOCK INSTALLATION
_______ PROCEDURE. FAST MOVEMENT OF THE DOORS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT IF THE LOCKS ARE NOT CORRECTLY INSTALLED.
 (2)  
Install the door locks for the wing and body landing gear (AMM 32-00-30/201).

 S 225-004

 (3)  
Examine the off-center dimension A with a straightedge and a scale.

 NOTE: If dimension A is not in tolerance, you must adjust the
____ strut. The tolerance is shown in Figure 501, View A-A.
 S 845-005
 (4)  
Release the pressure from hydraulic system No. 4 (AMM 29-11-00/201).

 S 495-006

 (5)  
Install the bungee clamp.

 NOTE: Tighten the bungee clamp to make sure the spring tension will
____
 decrease when you remove the apex bolt.

 S 865-007
 (6)  
Lift the airplane with jacks to decrease the load on the landing gear and the pressure on the apex bolt (AMM 07-11-01/201).

 S 035-008

 (7)  
Hold the upper jury strut and remove the apex bolt.

 S 015-009

 (8)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 1(151)