(9)  
AIPC 32-11-07 Fig. 2

 (10)
 AIPC 32-11-10 Fig. 2

 (11)
 AIPC 32-32-15 Fig. 1

 E.
Access

 (1)  
Location Zone
 735 Wing Landing Gear, LH
 745 Wing Landing Gear, RH

 F.
Prepare for the Procedure

 S 494-020
 WARNING:_______MAKE SURE THE BUNGEE TOOL IS ON THE DOWNLOCK BUNGEE. THE BUNGEE CAN EJECT FROM THE SIDE STRUT IF YOU TRY TO ASSEMBLE THE SIDE STRUT WITHOUT THE BUNGEE TOOL. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO THE EQUIPMENT.
 (1)  Make sure the bungee tool is on the downlock bungee
 (AMM 32-32-16/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-06
 ALL  ú ú 04 Page 406 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 224-021
 (2)  
Examine the fit of the structural connections for the lower side strut (AMM 32-11-06/601).

 S 494-022

 (3)  
Install the sling with the hoist on the lower side strut assembly.

 S 644-023

 (4)  
Prepare the lubrication insert (29) for installation into the spindle bolt (30).

 (a)  
Examine the O-rings (28) for deterioration or damage. 1) If it is necessary, replace the O-rings.

 (b)  
Apply a large quantity of grease to the O-rings (28) and the lubrication insert (29).

 (c)  
Apply a large quantity of grease to the inner surface of the spindle bolt (30).

 (d)  
Put the O-rings (28) on the lubrication insert (29).

 (e)  
If it is necessary, lubricate the lubrication insert (29) again.

 S 434-059
 (5)
Install the lubrication insert (29) into the spindle bolt (30).

 S 644-024

 (6)  
Prepare the lubrication insert (10) for installation into the apex bolt (13).

 (a)  
Examine the O-rings (11) for deterioration or damage. 1) If it is necessary, replace the O-rings.

 (b)  
Apply a large quantity of grease to the O-rings (11) and the lubrication insert (10).

 (c)  
Apply a large quantity of grease to the inner surface of the apex bolt (13).

 (d)  
Put the O-rings (11) on the lubrication insert (10).

 (e)  
If it is necessary, lubricate the lubrication insert (10) again.

 G.
Procedure

 S 434-072
 (1)  
Install the apex bolt (13):

 (a)  
Lubricate the shank and the threads of the apex bolt (13).

 (b)  
Align the top end of the lower side strut (6) with the lower end of the upper side strut (1).

 (c)  
Install the apex bolt (13) into the joint.

 (d)  
Install the bolt (12), the tang washer (15) and the retainer (16).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-06
 ALL  ú ú 04 Page 407 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (e)  Install the washer with the nut.
 NOTE:____ A socket with an extension is necessary to hold the head of the bolt (12).
 1)  Tighten the nut to 65-100 pound-inches.
 NOTE:____ Apply 65 pound-inches torque initially to the nut. Align the bolt hole and nut castellation as you slowly increase the torque. Do not apply more than 100 pound-inches. If the nut castellations and bolt hole do not align after you reach 100 pound-inches, remove the nut. Install additional washer and perform the same procedure again until you align the bolt hole within 65-100 pound-inches.
 2)  Install the cotter pin.
 (2)  S 434-060Install the hose bracket (9) with the bushings, the lockpin, and the retainer clamp.
 (3)  S 644-061Apply a large quantity of grease in the apex bolt (13) at the head of the bolt (12).
 NOTE:____ The longitudinal depth of the grease must be 0.50 to 0.75 inches in the apex bolt (13).
 (4)  S 434-062Install the lubrication insert (10) with the O-rings (11) into the apex bolt (13).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 1(140)