曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 6)  Make sure the gear UP message appears for the L, C, and R
 EIUs.
 7)  Wait 10 seconds after the UP indication comes in to view.
 8)  Make sure that the gear "UP" indication disappears from the
 upper EICAS gear display.
 9)  Make sure that door "CLOSED" indications appear on the
 EICAS "GEAR" lower display for all five landing gear at the
 end of the landing gear retraction cycle.

 10) Move the landing gear control lever to the OFF position. 11) Make sure the door CLOSED message appears on the EICAS GEAR
 lower display for all five landing gear.Move the landing gear control lever to the "DN" position. 1) Make sure that the gear in-transit indication on the upper
 EICAS gear display appears as soon as the landing gear starts extending.
 2) Make sure that the gear extends and that the doors close. a) Make sure the components attached to the landing gear do not interfere with the landing gear as it extends.
 3)  Make sure that the gear in-transit indication changes to the gear down indication on the upper EICAS gear display at the completion of the landing gear extension cycle.
 4)  Make sure that the door "CLOSED" indications appear on the EICAS "GEAR" lower display for all five landing gear at the end of the landing gear extension cycle.
Move the landing gear control lever to the "OFF" position. 1) Make sure that the EICAS "GEAR" lower display indicates "CLOSED" for all five gear doors with the lever in "OFF".
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-33-00
 ALL  ú ú 01 Page 507 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 495-017
 (17)
 Install landing gear ground lockpins in all landing gear (AMM 09-11-00/201).

 S 735-018

 (18)
 Do a test of the body gear and door operation.

 (a)  
Make sure that the landing gear control lever is in the "OFF" position.

 (b)  
Make sure that all landing gear doors are closed.

 S 095-019
 (19)
 Remove landing gear ground lockpins from all five landing gear (AMM 09-11-00/201).

 S 735-020

 (20)
 Continue the test of the body gear and door operation.

 (a)  
Make sure that all personnel are clear of the landing gear and landing gear doors.

 (b)  
Move the landing gear control lever rapidly to the UP position and into the detent. 1) Measure the time that the EICAS GEAR lower display

 indicates that the body gear doors are open.
 NOTE: Begin timing as soon as the body gear door
____ open indication is displayed.
 2)  Make sure that the period of illumination for the left (right) body gear door open indication does not exceed 16 seconds.
 3)  Make sure that door "CLOSED" indications appear on the EICAS "GEAR" lower display for each body landing gear at the end of the landing gear retraction cycle.
 (c)  
Move the landing gear control lever from the UP position to the OFF position.

 (d)  
Move the landing gear control lever rapidly to the "DN" position and into the detent. 1) Measure the time that the EICAS GEAR lower display

 indicates that the body gear doors are in the open condition.
 NOTE: Begin timing as soon as the body gear door
____ open indication is displayed.
 2)  Make sure that the period of illumination for the left (right) body gear door open indication does not exceed 25 seconds.
 3)  Make sure that the motion of the left (right) body gear door is smooth and moves at a linear rate.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-33-00
 ALL  ú ú 01 Page 508 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 4) Make sure that the time for the left (right) body gear door
 to close is 6 seconds.
 NOTE: Do not use EICAS indication to measure the door____
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(120)