(4)
C00712 Primer - MIL-P-8585, Color Y
C.
Parts
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 402 | 1 | Valve Assembly | 32-31-64 | 01 | 265 | | | 2 | Packing (O-Ring) | | | 235 | | | 3 | Ring (Backup Ring) | | | 260 | | | 4 | Packing (O-Ring) | | | 240 | | | 5 | Adapter | | | 220 | | | 6 | Packing (O-Ring) | | | 230 | | | 7 | Ring (Backup Ring) | | | 255 | | | 8 | Packing (O-Ring) | | | 225 | | | 9 | Adapter | | | 215 | | | 10 | Nut | | | 245 | | | 11 | Adapter | | | 210 | | | 12 | Bolt | | | 200 | | | 13 | Washer | | | 205 | | | 14 | Crank | | | 75 | 2.....….........…...................................…..........….....….........1
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-31-03
ALL ú ú 01 Page 412 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
D. References
(1)
09-11-00/201, Towing
(2)
29-11-00/201, Hydraulic Supply System
(3)
32-00-30/201, Landing Gear Door Locks
E.
Access
(1)
Location Zone
137 Body Landing Gear Wheel Well, LH
138 Body Landing Gear Wheel Well, RH
F.
Procedure
S 494-062
WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(1) Make sure you install the ground locks in all landing gear
(Ref 09-11-00/201).
S 494-063
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(2)
Do this task: "Installation of the Door Locks on the Doors for the Wing Landing Gear" (Ref 32-00-30/201).
S 494-064
(3)
Do this task: "Installation of the Door Locks on the Doors for the Body Landing Gear" (Ref 32-00-30/201).
S 434-072
(4)
Install the hydraulic fittings in the selector valve (1) (Fig. 401):
(a)
Lubricate the adapter fittings (5, 9 and 11), new O-rings (2,4,6 and 8) and backup rings (3 and 7) with Skydrol Assembly Lube.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-31-03
ALL ú ú 01 Page 413 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(b) Install the adapter fittings (5, 9 and 11), new O-rings (2,4,6
and 8) and backup rings (3 and 7) in the selector valve (1).
S 614-075
(5) Fill the valve (1) with fire-resistant hydraulic fluid.
S 034-074
(6) Install a cap on the valve ports.
S 424-073
(7) Install the selector valve (1):
(a) Apply the wet primer to all areas of the bolt holes.
(b) Install the selector valve (1) in its position.
(c) Install the mounting bolts (12) and washers (13).
(d) Attach the selector valve crank (14) to the valve shaft.
NOTE: The joint with splines has index marks on it to make____
sure you put the shaft in the correct position.
(e) Apply corrosion preventive compound around all areas of the
joint.
(f) Remove the caps and plugs from the hydraulic hoses.
(g) Connect the hydraulic hoses to the valve (1).
S 094-025
(8) Remove the rigging pin from the selector valve quadrant.
S 494-066
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO REMOVE
_______ THE DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(37)
