LOCK CLOSED
Uplock Actuating Tool
Figure 402 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-32-14
ALL ú ú 01 Page 404 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
LOCK/CLOSE
LOCK OPEN (ALTERNATE METHOD)
Uplock Actuating ToolFigure 402 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-32-14
ALL ú ú 01 Page 405 ú Oct 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(4)
D00013 Grease - MIL-G-23827 (optional)
B.
Parts
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Actuator | 32-32-51 | 02 | 195 | | | 2 | Adapter | 32-32-14 | 01 | 30 | | | 3 | Backup Ring | | | 25 | | | 4 | O-ring | | | 20 | | | 5 | Pin, Cotter | 32-32-51 | 02 | 180 | | | 6 | Nut | | | 185 | | | 7 | Washer | | | 190 | | | 10 | Adapter | 32-32-14 | 01 | 15 | | | 11 | Backup Ring | | | 10 | | | 12 | O-ring | | | 05 | | | 13 | Washer | 32-32-51 | 02 | 250 | | | 15 | Nut | | | 175 | | | 16 | Pin, Cotter | | | 150 | | | 17 | Washer | | | 160 | | | 18 | Bolt | | | 155 | | | 20 | Washer | | | 165 | | | 21 | Washer | | | 175 | 2......…........…...................................…..........….....….........1
C. References
(1)
AMM 09-11-00/201, Towing
(2)
AMM 29-11-00/201, Main Hydraulic Supply System
(3)
AMM 32-00-30/201, Landing Gear Door Locks
D.
Access
(1)
Location Zone
735 Wing Landing Gear, LH
745 Wing Landing Gear, RH
E.
Procedure
S 424-008
(1)
Install the hydraulic fittings in the valve (Fig. 401):
(a)
Lubricate the O-rings (4 and 12), the backup rings (3 and 11), and the fittings (2 and 10) with Skydrol Assembly Lube.
(b)
Install the hydraulic fittings (2 and 10) with new O-rings (4 and 12) and backup rings (3 and 11).
(2)
Extend the actuator (1).
(3)
Fill the actuator with hydraulic fluid.
S 864-025
S 614-024
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-32-14
ALL ú ú 01 Page 406 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 034-023
(4)
Install caps on the hydraulic ports.
S 424-026
(5)
Install the actuator:
(a)
Put the actuator (1) in its position with the rod end down and outboard and the hydraulic ports up.
(b)
Install the head end of the actuator (1) on the hook pivot pin (14) with the washer (13).
NOTE: Make sure the countersink on the washer is adjacent to
____
the bottom of the pin.
(c)
Install the washer (7) and the nut (6).
(d)
Tighten the nut (6) to 100 pound-inches maximum.
(e)
Loosen the nut to permit the installation of the cotter pin (5).
CAUTION: MAKE SURE YOU INSTALL THE BOLT (18) AS SHOWN IN FIG. 401.
_______ IF YOU INSTALL THE BOLT HEAD IN THE OTHER DIRECTION IT CAN TOUCH THE UPLOCK SPRINGS.
(f)
Connect the rod end of the actuator (1) to the clevis (19) with the parts that follow: 1) The bolt (18) with the countersunk washer (17) adjacent to
the bolt head 2) The washers (20 and 21) adjacent to the nut (15).
(g)
Tighten the nut (15) to 100 pound-inches maximum.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(92)
