2)  Make sure the upper EICAS display does not show the GEAR DISAGREE (CAUTION) message.

 (b)  
Move the control lever to the OFF position.

 1)  Make sure the upper EICAS display shows the GEAR DISAGREE (CAUTION) message.
 NOTE: The GEAR DISAGREE indication will not show for
____ approximately 25 to 35 seconds after you move the control lever. This occurs when you move the control lever from the DN to OFF or the DN to UP positions.
 (c)  Move the control lever to the UP position. 1) Make sure the upper EICAS display shows the GEAR DISAGREE (CAUTION) message.
 2)  Make sure the upper EICAS display shows the GEAR DOOR (ADVISORY) message.
 NOTE: The GEAR DOOR indication will not come into view for
____ approximately 25 to 35 seconds after the doors open.
 3)  Make sure the upper EICAS display shows a symbol for each of the four landing gear.
 NOTE: If the landing gear moves while in the locked down
____ position, an in-transit condition can show. This can occur as an alternative to the DN condition.
 4)  Make sure the lower EICAS display shows all four landing gear doors open (four slashed boxes).
 S 485-126
 WARNING: MAKE SURE THAT THE GROUND LOCKS ARE INSTALLED IN ALL OF THE
_______ LANDING GEAR. WITHOUT THE GROUND LOCKS, THE LANDING GEAR CAN RETRACT AND CAUSE INJURIES TO PERSONS AND DAMAGE TO THE EQUIPMENT.
 (6)  Make sure the ground locks are installed in the nose and main landing gear (AMM 09-11-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-00
 ALL  ú ú 01 Page 513 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 485-127
 WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
 (7)  
Open the doors for the landing gear and install the door locks (AMM 32-00-30/201).

 S 865-128

 (8)  
Make sure the door actuators for the main gear doors hold the doors open.

 S 485-087

 (9)  
Install the rigging pins (WD-1 LH, WD-2 RH) in the left side and the right side door-operated sequence valves.

 (a)  
Make sure the rigging pins do not rub when you install them.

 S 865-129
 (10)
 Move the control lever to the OFF position.

 S 485-130

 (11)
 Install the rigging pins (WD-5 and WD-6) in the left side and the right side downlock-operated sequence valves.

 (a)  
Make sure the rigging pins do not rub when you install them.

 S 085-131
 (12)
 Remove the rigging pins from the door-operated sequence valves.

 S 085-132

 (13)
 Remove the rigging pins from the downlock-operated sequence valves.

 S 085-133
 WARNING:_______OBEY THE REMOVAL PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
 (14)
 Remove the door locks (AMM 32-00-30/201).

 (15)
 Remove the ground locks from the landing gear (AMM 09-11-00/201).

 S 095-095
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-00
 ALL  ú ú 01 Page 514 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 865-096
 WARNING:_______ MAKE SURE ALL PERSONS AND EQUIPMENT ARE AWAY FROM THE LANDING
 GEAR DOOR OPERATION AREA.  A FAST MOVEMENT OF THE LANDING GEAR
 DOORS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.

 (16) Move the ground release handles for the main landing gear to the doors closed position.
 S 735-097
 WARNING: MAKE SURE ALL PERSONS AND EQUIPMENT ARE AWAY FROM THE LANDING
_______ GEAR AND DOOR OPERATION AREA. A FAST MOVEMENT OF THE LANDING GEAR AND DOORS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (17)
 Do these steps to test the gear and gear doors indication:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(57)