S 494-009

 (2)  
Install the bungee clamp on the bungee assembly.

 S 424-010

 (3)  
Install the downlock bungee (Fig. 401):

 (a)  
Install the bungee between the lower jury strut and the upper side strut.

 NOTE: You will connect the rod end to the lower jury strut and
____ the head end to the upper side strut.
 (b)  
Lubricate the bolt shanks and the washer faces with grease.

 (c)  
Install the bolts at the two ends of the bungee.

 (d)  
Tighten the nuts to 360-420 pound-inches.

 (e)  
Loosen the nut to align the nearest castellation with the hole in the bolt.

 (f)  
Install the cotter pin.

 (g)  
Lubricate the grease fittings in each bolt head.

 S 094-011
 (4)  Carefully remove the bungee clamp.
 S 094-014
 WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASKS BELOW TO REMOVE
_______ THE DOOR LOCKS FROM THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT REMOVE THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (5)  
Do this task: "Body Landing Gear Door Lock Removal"
 (AMM 32-00-30/201).

 S 094-013

 (6)  
Do this task: "Wing Landing Gear Door Lock Removal"
 (AMM 32-00-30/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-16
 ALL  ú ú 01 Page 404 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 WING LANDING GEAR DOOR ACTUATOR SWIVEL JOINT - REMOVAL/INSTALLATION
___________________________________________________________________
 1.  General
_______
 A.  This procedure contains these two tasks:
 (1)  
The removal of the swivel joint for the door actuator of the wing landing gear

 (2)  
The installation of the swivel joint for the door actuator of the wing landing gear.

 B.  
To remove the swivel joint these operations are necessary:

 (1)  
Remove the attach bolts from the swivel joint.

 (2)  
Make sure the swivel joint turns freely.

 C.  
To install the swivel joint these operations are necessary:

 (1)  
Lubricate the O-rings and the backup rings.

 (2)  
Install the swivel joint with the screw and the lockwire.

 (3)  
Do a check of the swivel joint operation.

 D.  
The swivel joints connect the door actuator to the hydraulic system. They are in the wheel well for the wing landing gear. Use this procedure to remove and install the seals and the joints if you find them defective.

 TASK 32-32-26-004-001
 2.  Wing Landing Gear Door Actuator Swivel Joint Removal
____________________________________________________
 A.  References
 (1)  
09-11-00/201, Towing

 (2)  
29-11-00/201 Main Hydraulic Supply System

 (3)  
32-00-30/201, Landing Gear Door Locks

 (4)  
IPC 32-32-27 Fig. 1

 B.  
Access

 (1)  
Location Zone
 135 Wing Landing Gear Well, LH
 136 Wing Landing Gear Well, RH

 C.  
Procedure

 S 494-016
 WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1) Install the ground locks in all landing gear (Ref 09-11-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-32-26
 ALL  ú ú 01 Page 401 ú Feb 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

SEE A
SEE B
A
DOOR ACTUATOR
BACKUP RINGS
O-RINGS
BACKUP RINGS
SWIVEL JOINT
ATTACH SCREW (3 LOCATIONS EACH JOINT)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 4(98)