S 485-215
 (20)
 Apply power supply voltage to the contact B2 of the relay socket DR1104.

 S 865-216

 (21)
 Slowly increase the voltage (on contact B2) to 65 volts DC and do these checks:

 (a)  
Make sure current flows through contact B2 between 45 to 57 volts.

 (b)  
Make sure the voltage on the voltmeter increases with the power supply voltage and remains constant after the current flows through contact B2.

 NOTE:  The current flow occurs through contact B2 when the voltmeter reads 45 to 57 volts DC. The voltage on contact B2 remains in this range even though the power supply voltage is increased more than 57 volts.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-31-00
 ALL  ú ú 02 Page 542 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (c)  
Reverse the polarity of the power supply and the voltmeter.

 (d)  
Make sure voltage stays the same when the power supply and the voltmeter is reversed.

 S 085-195
 (22)
 Remove the test equipment.

 S 425-221

 (23)
 Connect the electrical connector on the latch actuators.

 S 035-196

 (24)
 Connect the electrical connector D6141 on the latch actuator test module.

 S 865-197

 (25)
 Install the isolation relay R1104.

 S 865-198

 (26)
 Close the access door to the pressure switch S110 and isolation relay R1104.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-31-00
 ALL  ú ú 02 Page 543 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 NOSE CARGO DOOR SYSTEM - INSPECTION/CHECK
_________________________________________
 TASK 52-31-00-706-001
 1.  Nose Cargo Door System Quick Check (Fig. 601)__________________________________
 A. General
 (1)  
This procedure gives instructions to do a quick check to find the misrigging or deterioration in the rigging of the nose cargo door system. The procedure is not a complete system test. For a complete system test refer to AMM 52-31-00/501.

 B.
Standard Tools and Equipment

 (1)  
Spring Scale - Push-Pull type, 100-pound capacity

 (2)  
Torque Wrench (with dial indicator) - 0-100 pound-inches range

 (3)  
Speed handle or ratchet - 1/4-inch hex drive socket

 C.
References

 (1)  
AMM 52-31-00/201, Nose Cargo Door

 (2)  
AMM 52-31-00/501, Nose Cargo Door

 (3)  
AMM 52-31-09/401, Nose Cargo Door Push-Pull Cam

 (4)  
FIM 52-EICAS MESSAGES

 D.
Access

 (1)  
Location Zone
 801 Nose Cargo Door

 E.
Procedure

 S 866-002
 (1)  
Close the nose cargo door.

 S 226-003

 (2)  
On the two linear actuators, make sure the end of actuator shaft covers the inspection hole 1/4 to 3/4 inch (Detail A, Fig. 601).

 S 716-004

 (3)  
Do these steps if the ends of the actuator shafts are not in the correct positions:

 (a)  
Open the nose cargo door a minimum of 24 inches at the bottom.

 (b)  
Fully close the nose cargo door.

 (c)  
Make sure the ends of the actuator shafts are in the correct positions.

 S 826-005
 (4)
If the ends of the actuator shafts are still not in the correct positions, adjust the linear actuators (AMM 52-31-00/501).

 (5)
Make sure the nose cargo door is fully closed and latched.

 S 866-006
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 2(23)