R (g) Safety the oil filler plug (81) with the lockwire MISCELLANEOUS
R (Material No. 19-010).
R (h) Connect the breather cap (80) to the oil filler plug (81).
(2) Installation of the oil drain plug (86).
R (a) Remove the PLUG - BLANKING from the opening for the oil drain
R plug (86) in the THS actuator (1).
R (b) Make sure that the oil drain plug (86) and the plug interface are
R clean.
R (c) Lubricate the new O-ring (87) with the oil OILS (Material No. 03-
003).
R (d) Put the new O-ring (87) in position on the oil drain plug (86).
R (e) Install the oil drain plug (86) in the THS actuator (1).
R (f) TORQUE the oil drain plug (86) to between 1.4 and 1.6 m.daN
R (10.32 and 11.79 lbf.ft).
R (g) Safety the oil drain plug (86) with the lockwire MISCELLANEOUS
R (Material No. 19-010).
R (h) Install the protective cap (84), with the magnetic chip detector
R (85), on the oil drain plug (86).
R (i) Fill the THS actuator (1) with the correct oil to the necessary
level (Ref. TASK 12-13-27-612-001).
R (j) Remove the drainage container from below the THS actuator (1).
5. Close-up________
Subtask 27-44-51-210-053
A. Do a visual check of the THS actuator and make sure that there are no
leaks from:
- the oil filler plug and adaptor,
- the oil drain plug.
Subtask 27-44-51-410-051
B. Close Access
(1)
Remove the warning notices.
(2)
Make sure that the work area is clean and clear of tools and other items.
(3)
Close the access door 312AR.
(4)
Remove the access platform(s).
1EFF : ALL 1 27-44-51Page 442 1 1 May 01/05R 1 1 1CES 1
TASK 27-44-51-000-003
Removal of the Lower Claw Stop
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific warning notices No specific access platform 5.5 m (18 ft. 1 in.) 0U145409 1 SPECIAL WRENCH 0U145920 1 TOOL - MANUAL CRANKING STOP, THS ACTUATOR 0U190360 1 PIN - RIGGING 0U190844 2 RELEASE TOOL - PRESSURE-OFF BRAKE, THS ACTUATOR 98D27403500000 1 PITCH TRIM CONTROL LOCKING
1EFF : ALL 1 27-44-51Page 443 1 1 May 01/05R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-44-51-710-001 Operational Test of the No-Back Device (No-Back Pawls) 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
29-23-00-863-001 Pressurize the Green Hydraulic System from the Yellow Hydraulic System through the PTU with the Electric Pump
29-23-00-863-002 Pressurize the Yellow Hydraulic System from the Green Hydraulic System through the PTU with the Ground Service Cart
27-44-51-991-001 Fig. 401 27-44-51-991-016 Fig. 408
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(155)
