-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______ CARBONFIBER REINFORCED PLASTIC.
NOTE : The removal of the elevator servo control actuator 34CE1 mode selector
____ valve transducer is given. The removal of the servo control actuator 34CE2, 34CE3 and 34CE4 mode selector valve transducers are the same.
1. Reason for the Job__________________ Self Explanatory
1EFF : ALL 1 27-34-51Page 452 1 1 May 01/05R 1 1 1CES 1
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific warning notices No specific access platform 3.5 m (11 ft. 6 in.) 98D27309001000 1 TOOL-ELEVATOR NEUTRAL SETTING 98D27903500000 2 PIN-SIDE STICK LOCKING
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 55-13-11-000-001 Removal of the THS Trailing Edge Access Panels 27-34-51-991-005 Fig. 406
3. Job Set-up
__________
Subtask 27-34-51-860-066
A. Aircraft Maintenance Configuration
(1) Make sure that the elevators and the horizontal stabilizer controls are set to the neutral position.
Subtask 27-34-51-860-055
B. Depressurize Hydraulic Systems
(1) Depressurize the Green, Yellow and Blue hydraulic systems. (Ref. TASK 29-10-00-864-001) (Ref. TASK 29-10-00-864-002) (Ref. TASK 29-10-00-864-003)
1EFF : ALL 1 27-34-51Page 453 1 1 May 01/05R 1 1 1CES 1
Subtask 27-34-51-865-058
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/FCDC1/SPLY 20CE1 B10 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 121VU FLIGHT CONTROLS/FCDC2/SPLY 20CE2 Q20 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
Subtask 27-34-51-481-052
D. Install Locking Devices
(1)
Put the PIN-SIDE STICK LOCKING (98D27903500000) in the CAPT and F/O side stick controllers.
(2)
Install the TOOL-ELEVATOR NEUTRAL SETTING (98D27309001000) on the elevator.
Subtask 27-34-51-941-055
E. Safety Precautions
(1)
Put the warning notices in the flight compartment to tell persons not to operate the flight controls.
(2)
Put the warning notices in position to tell persons not to operate the hydraulic systems.
(3)
Put the access platform in position at zones 334 for the left hand trailing edge access panels and/or zone 344 for the right hand trailing edge access panels.
1EFF : ALL 1 27-34-51Page 454 1 1 May 01/05R 1 1 1CES 1
Subtask 27-34-51-010-055
F. Access
(1) Open the trailing edge access panels 334DB and/or 344DB (Ref. TASK 55-13-11-000-001).
4. Procedure
_________
(Ref. Fig. 406/TASK 27-34-51-991-005) Subtask 27-34-51-020-061
A. Disconnect Electrical Connectors
(1) Disconnect the electrical connectors.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱3(71)
